GSM alarm system, 10 telephone numbers for dialing and SMS, 3 built-in relays 5A, power supply 12V, 4 control zones for connecting alarm loops with sensors. Built-in analog temperature sensor.
KSITAL GSM-4T - cellular control system for heating equipment. It is intended for notification via a cellular communication channel about the failure of heating equipment and remote control them with a cell phone.
The KSITAL GSM-4T system has two heating control functions: maintaining the temperature at a level set remotely via SMS, and alerting when the temperature drops below the set minimum value or when the temperature exceeds the maximum set value. On a daily basis or upon request, the system can send readings of all temperature sensors connected to the controller. Remote digital temperature sensors(up to 5 pcs.) can be removed at a distance of up to 100 m from the system, operate in the range from -55 ° C to + 125 ° C with an accuracy of 0.5 ° C. The system allows you to have information about the temperature at various points of the controlled room, including the temperature of the coolant. One of the sensors, whose number is specified in the settings, is used to stabilize the temperature it measures. This can be either the air temperature in the room, or the temperature of the coolant. The GSM system stabilizes the temperature by turning the heating on and off using one of the built-in relays. Retransmits boiler alarm signals via SMS. Allows remote restart of the boiler. Easily adaptable for control freezers, server rooms, air conditioning systems, signaling that the controlled temperature is out of the acceptable range. Along with this, it supports all the functions inherent in a GSM alarm system: notification via SMS and voice dialer about the operation of security, fire and other sensors, turning on a siren, listening to a room, etc.
The KSITAL GSM-4T system has a wide scope, the ability to create a large number of configurations and settings, but at the same time, exceptional simplicity and clarity of the initial launch and installation. To do this, just insert a blank SIM card into the controller, turn on the 220V power adapter and call from your mobile phone to the number of this SIM card. The controller itself will create the initial “default” settings, templates for the SMS mailing list and the list for voice dialing, by AON it will “capture” your number and add it to these lists. Just a minute after the launch, you just need to call the controller's SIM card number, wait for the call to be reset, and you will receive a response SMS containing information about the status of the inputs, the status of the built-in relays, the temperature at the facility, the system is armed or disarmed, the presence 220V.
Installation is also made easy. No need to solder the connectors, security loops are connected through convenient, easily accessible terminal blocks. If errors were made during installation, then when arming, the system will send an SMS, where it will mark short circuits or breaks for each loop. In the case when it is not possible to lay wires to the sensors at the facility, radio sensors from different manufacturers can be used, while a receiver of the same manufacturer is connected to the KSITAL GSM-4T controller.
Peculiarities:
- Easy programming without using a computer
- Possibility to make changes to the system settings remotely via SMS
- Sending SMS about arming and disarming
- Room temperature measurement and transmission, temperature remote control
- Panic button function
- Automatic daily report on the operation of the system, as well as by SMS request or by call
- It is possible to notify about the operation of sensors at the facility: security, fire, gas, water leaks, as well as when 220V is turned off, discharge backup battery, falling temperature below the set level or exceeding the maximum.
New options:
- Remote request for the balance of the active SIM card allows you to find out the balance in a timely manner and avoid blocking the account.
- Installing two SIM-cards allows you to switch to work with a backup cellular operator in case of technical problems with the main operator.
- The anti-jamming function performs continuous remote monitoring of the presence of the KSITAL system in the network and informs the user about the loss of communication in the event of GSM jamming.
- The ability to significantly increase the number of inputs and relays by connecting one or more expansion units (each includes 12 control loops and 4 relays 220V/5A for equipment control).
Functionality:
Built-in GSM module. 10 telephone numbers for sending SMS and for dialing with a voice message 4 control zones for connecting alarm loops with sensors. 3 built-in relays 5A/220V for equipment control. One built-in and two remote (with the possibility of increasing up to 5 pieces) temperature sensors for measuring and transmitting the temperature in the room. The ability to install additional 6 Touch Memory keys, in addition to the master key included in the kit. The ability to listen to the room with an external microphone. Possibility of programming by the user of long (up to 60 characters) SMS corresponding to the triggering of control zones. Possibility to send SMS about the setting and removal of control from the object. Sending SMS in case of a critical drop in room temperature. The function of stabilizing the temperature in the room according to a remote task. Uninterruptible power supply function, control of charging of the backup 12V battery, sending SMS in case of power failure 220V and critical discharge of the backup battery. Panic button function that allows you to send alarm SMS when the system is removed from control. Automatic daily report (and also on request) on the health of the system. Putting the system on control both with the help of Touch Memory keys and with the help of SMS. Diagnosis of malfunction of alarm loops (breaks, short circuits) during control. Power supply 12V directly from the controller (maintained in case of loss of 220V). The controller reads the voltage at the inputs of the security zones in analog form and compares it with the values recorded during arming. An alarm for a given zone is defined as a significant (more than 25% of that measured during setting) voltage deviation at the zone input, caused by a change in the loop resistance. Therefore, "Ksital GSM-12T" can work with any sensors that provide a break in the security loop, or its short circuit, or a change in the resistance of the loop. These include almost all security and fire sensors, flood sensors, gas leakage sensors, etc. of any zone according to the list of phones, an SMS is sent, which indicates the number of the triggered zone (default text) or a text previously entered by the user. Then this mailing is duplicated by dialing with a voice message “Alarm! » according to the additional list of telephones, where there may be ordinary landline numbers. If necessary, a relay is simultaneously activated, including a siren, searchlight, etc. The 1st zone has a user-programmable activation delay in the range from 1 to 99 seconds (default 20 seconds). Sensors that control the entrance door and the hallway are connected to this zone. This delay allows the owner of the registered Touch Memory key to disarm the system by applying it to the reader included in the kit and installed in the hallway. Arming and disarming can be accompanied by sending control SMS to the main phone indicating the time. This allows, for example, to control the time of arrival and departure of children from home. The controller includes one built-in and two remote temperature sensors. Remote temperature sensors are connected in series with the Touch Memory reader common cable up to 100m long. Quantity remote temperature sensors can be increased up to 5 pcs. The system is equipped with a power supply that provides power to the controller from the 220V network, as well as charging a backup 12V lead battery. When 220V is lost, the system (and sensors connected to it) are switched to power from the backup battery. At the same time, an SMS is sent about the loss of 220V. Corresponding SMS are sent when the backup battery is discharged and when 220V is restored. By commands sent in the form of SMS, any of the 3 built-in relays can be turned on or off. This makes it possible to remotely control various equipment. Switching on and off is accompanied by sending a confirmation SMS. A system health report containing the status of relays, inputs, readings of temperature sensors and other parameters can be received by SMS request, just by call (if the SIM card supports Caller ID) or daily without a request.
Specifications:
The system is designed for installation inside a monitored facility and is designed for round-the-clock operation at temperatures from -25°C to +50°C. Work at negative temperatures requires the use of a SIM card of the appropriate temperature range.
Power consumed by the system from the network alternating current- no more than 10W
Number of built-in relays - 3.
The number of control zones (entrances) - 4.
The maximum number of phone numbers in the list to which SMS messages are sent is 10.
The maximum number of phone numbers in the list that can be dialed with the voice message "Alarm!" - ten.
Overall dimensions of the controller - 15 x 11 x 4 cm.
Package size - 25 x 16 x 6 cm.
Weight with packaging - 850 g.
Description Xital GSM-4m
Russian-made GSM alarm system "Ksital 4m" with USB input is designed to protect houses, garages, cars, apartments, provide fire safety in summer cottages with 4-channel information transmission via SMS and a personal computer.The Xital GSM-4m system has a wide scope, the ability to create a large number of configurations and settings, but at the same time, exceptional simplicity and clarity of initial launch and installation. The main purpose of the signaling module:
- Principle of operation
- Remote request for the balance of the active SIM card allows you to find out the balance in a timely manner and avoid blocking the account.
- Installing two SIM-cards allows you to switch to work with a backup cellular operator in case of technical problems with the main operator.
- The ability to significantly increase the number of inputs and relays by connecting one or more expansion units (each includes 4 control loops and a 220V/5A relay for equipment control).
USB module allows:
Connecting the Xital GSM-4m system
The controller includes built-in temperature sensor. To a separate input for connecting the reader touch memory it can also be connected additionally up to 5 remote digital temperature sensors operating in the range from -55°С to +125°С. The user can use SMS to set the temperature value at which one of the built-in relays will operate. The system kit includes power unit, which provides power to the controller from the 220V network, as well as charging a backup 12V lead battery. When 220V fails, the system (and sensors connected to it) switch to power from backup battery. At the same time, an SMS is sent about the loss of 220V. Corresponding SMS are sent when the backup battery is discharged and when 220V is restored. By commands sent in the form of SMS, any of the 3 built-in relays can be turned on or off. Thus, you can remotely control various equipment. Switching on and off is accompanied by sending a confirmation SMS.
- Installation of alarm system Ksital 4 (independently)
- Call from your mobile phone to the number of this SIM card. The controller itself will create the initial settings "by default", templates for the SMS mailing list and the list for voice dialing, by Caller ID (automatic number identification) will add your number to these lists.
- A minute after the launch, you just need to call the controller's SIM card number, wait for the call to be reset, and you will receive a response SMS containing information about the status of the inputs, built-in relays, temperature at the facility, whether the facility is armed, and about availability of 220V power supply.
- Installation of the gsm alarm system (on your own) is also facilitated.
- No need to solder the connectors, security loops are connected through convenient, easily accessible terminal blocks. If errors were made during installation, then when arming gsm system 4 will send an SMS, where it will mark short circuits or breaks for each loop.
- In the case when it is not possible to lay wires to the sensors at the facility, radio sensors from different manufacturers can be used, while a receiver of the same manufacturer is connected to the Xital GSM-4m controller.
It is enough to insert a blank SIM card into the controller, turn on the power adapter to the 220V network.
Notification, settings, sensor zoning
The security zone alarm is defined as a significant (more than 25% of that measured during arming) voltage deviation at the zone input, caused by a change in the loop resistance. Therefore, "Ksital GSM-4m" can work with any sensors that provide a break in the security loop, or its short circuit, or a change in the resistance of the loop. These include almost all security and fire sensors(flood sensors, gas leaks, etc.).
Each security zone in the settings can be configured either as permanently enabled, or as permanently disabled, or as armed with Touch Memory or SMS keys. When any zone is triggered, an SMS is sent to the list of phones, which indicates the number of the triggered zone (default text) or a text previously entered by the user. Then this mailing is duplicated by dialing with a voice message "Alarm!" according to an additional list of telephones, where there may be ordinary landline numbers. If necessary, a relay is simultaneously activated, including a siren, searchlight, etc.
The 1st zone of Xital-4 has a delay for operation programmed by the user in the range from 1 to 99 seconds (by default 20 seconds). Sensors that control the entrance door and the hallway are connected to this zone. This delay allows the owner of the registered Touch Memory key to disarm the system by applying it to the reader included in the kit and installed in the hallway.
Arming and disarming can be accompanied by sending control SMS to the main phone indicating the time. This allows, for example, to control the time of arrival and departure of children from home.
A report on the operability of the gsm alarm system, containing the status of relays, inputs, readings of temperature sensors and other parameters, can be received by SMS request, just by call (if the SIM card supports Caller ID) or daily without a request.
Professional installation. We recommend ordering from our company. The specialists of the company will create effective system protection for your offices, shops, banks, hotels, country houses and housing and communal services. Fire alarm equipment is implemented on the basis of foreign systems Crow, Pyronix, GSN, Optex, System Sensor and leading domestic manufacturers.
Our solutions are used by security firms, service companies, homeowners associations, etc. organizations for remote control of complex engineering equipment (heating boilers, water supply pumps, power supply sources, lighting and irrigation systems for greenhouses) and integrated security of the facility!
Xital gsm 4 alarm system for security, fire alarm, control of electrical appliances in an apartment and a country house
GSM-4 complete set:
- Reader of electronic keys Touch Memory
- Remote GSM antenna
- Power Supply
- Master key
- Cord for connecting a backup battery
- Instruction
Advantages and features of 4 gsm model alarms:
Specifications Xital GSM-4m
- Unit: 1 piece
- Dimensions (mm): 250x160x60
- Weight (kg): 0.85
- Mode of operation: from -25 gr. C to +50 gr.C
- Overall dimensions of the controller: 15x11x4 cm
- Power consumed by the system from the AC mains: no more than 10W
- Number of control zones (entrances): 4
- Package size: 25x16x6 cm.
- Weight with packaging: 850 g
- The maximum number of phone numbers in the list to which SMS messages are sent is 10.
- Number of built-in relays: 3
- Operation at low temperatures requires the use of a SIM card of the appropriate temperature range
It is a controller to which security or fire sensors are connected. The built-in GSM module is used as a transmitter.
When any sensor is triggered, an SMS message is sent indicating the violated zone according to the list of telephones (up to 10 numbers) previously stored in memory.
Controls up to 12 security zones, has 3 relays to control actuators.
It is used for the protection of cottages, apartments, control of heating and technological equipment, power failure 220V, etc.
GENERAL INFORMATION AND BASIC PARAMETERS
The cellular notification and control system KSITAL GSM-4T is designed for remote monitoring and control of stationary non-telephonized objects using a cellular phone. It can be: a house, a summer house, an apartment, an office, a warehouse, a retail outlet, a garage, etc.
Using SMS and voice dialing, the system informs about the operation of various sensors connected to the controller inputs. These can be motion, vibration, glass breaking, smoke, gas leakage, flooding, pressure sensors, or simply door bell. The message text for each input can be changed according to the purpose of the sensor.
Messages are sent sequentially to a pre-recorded list of phones.
Upon receipt of an SMS message with a control command, the controller can turn on or turn off any of the three relays built into it. In this way, various devices such as heating, sauna, pumps, lighting, etc. can be remotely controlled. from a cell phone.
One built-in and up to five remote temperature sensors continuously measure the temperature in the room. The system collects data from all connected temperature sensors and sends them in a report in the form of a table.
When the room temperature goes beyond the specified range, SMS messages about this are sent to cell phones, the numbers of which are previously entered in the telephone directory on the SIM card.
The system has a mode of automatic maintenance of the temperature in the room, controlling heating system using the built-in relay. The stabilization temperature value is set by an SMS command from a remote cell phone. You can simultaneously set two room temperature values - day and night. This will allow in case electric heating Significantly save on electricity bills by setting the night temperature higher than the daytime temperature. At the same time, heating will mainly work at night, warming up the room at a cheaper rate.
The following can be easily connected to the controller: an external status indicator "under control", for example, a street light annunciator, or a control panel for an additional alarm system.
If there is a possibility of a 220V voltage shutdown at the facility, then a 12V backup battery must be used, which will be charged by the controller as needed.
If there is a backup battery, the system remains fully operational during a 220V power outage, reports the loss/appearance of voltage and the discharge of the backup battery.
There are two SIM-card readers installed on the controller board, one for the main and one for the backup operator. The system will automatically switch to a backup operator in case of loss of the network of the main operator or failures in the transmission of SMS through it. The possibility of sound control of the room with the help of additional external microphones is provided.
The presence of two Xital GSM systems, remote from each other and configured as "partners", allows you to timely fix problems with the cellular network or the use of jamming radio signals.
The system is intended for installation inside a monitored facility and is designed for round-the-clock operation at temperatures from -350C to +500C.
The power consumed by the system from the AC mains is not more than 10 watts.
Number of built-in relays - 3.
The maximum switched power of the relay contacts is 200 watts.
The number of control zones (entrances) - 4.
The maximum number of phone numbers for sending SMS messages is 10.
Maximum number of telephone numbers for dialing with a voice message
"Anxiety!" - ten.
Overall dimensions of the controller - 15 x 11 x 4 cm.
Package size - 25 x 16 x 6 cm.
Weight with packaging - 850 g.
SYSTEM DEVICE
The system includes:
KSITAL GSM-4T controller; with built-in GSM module
GSM antenna
power adapter
Touch Memory electronic key reader
Touch Memory master key
backup battery 12V (supplied separately)
Touch Memory electronic keys (sold separately)
additional remote digital temperature sensors (supplied separately)
detectors, sensors (supplied separately)
executive devices(supplied separately)
external microphone (sold separately)
remote expansion units (supplied separately)
CONTROLLER KSITAL GSM-4T
INTEGRATED DEVICES
Built-in GSM module
temperature sensor
Backup battery charger and uninterruptible power supply system
Touch Memory electronic key controller
Relay for controlling additional devices (3 pcs.)
The built-in temperature sensor is located on the controller board inside the case. The sensor has an accuracy of ±1.50С.
The backup battery is charged in the presence of a 220V network.
The charge level of the backup battery is not guaranteed when the mains voltage is below 200V or when using a non-standard adapter.
In the presence of a backup battery, the controller provides uninterrupted power to the sensors connected to it constant voltage 12V.
The controller of the Touch Memory electronic key reader is implemented on the KSITAL GSM board. Digital code packets pass through the wires connecting the reader and the controller. This eliminates the possibility of controlling the controller modes by manipulating the wiring, such as removing from control without having a registered key.
The KSITAL GSM controller has 3 built-in relays. The relay output contacts are brought to the external terminals. Relays are used for automatic or SMS-command control of various devices. Relay contacts are designed for voltage up to 240V. For reasons of reliability and durability of the relay, it is undesirable to connect powerful devices (more than 200 watts) directly to the controller.
SIM READERS
The controller board has two SIM card readers, labeled SIM1 and SIM2. The SIM card of the main mobile operator is installed on the SIM1 position, and the SIM card of the backup operator is installed on the SIM2 position, if necessary. The system will switch to a backup operator in case of loss of the network of the main operator or failures in the transmission of SMS through it.
SENSOR CONTROL INPUTS
Up to 4 zones can be allocated on a controlled object. Each of the zones can be represented by a resistor and any required number of sensors connected in one loop and connected to one of the 4 controller inputs and the "COM" terminal.
The recommended total loop resistance is 3.6 kOhm. With this resistance, the voltage at the zone input will be approximately 7.2V. This is 50% of the voltage that occurs at the zone input when the loop breaks (100% corresponds to the voltage at the battery terminals).
The zone is considered violated if the voltage at the zone input goes beyond the specified range (normal). By default, this range is set from 25% to 75%. Thus, a break in the loop (voltage = 100%) or shorting the input to the "COM" terminal (voltage = 0%) will trigger the input. The range limits can be changed separately for each
Upon delivery, the controller is equipped with a detachable GSM standard antenna with a cable length of 2.5 m. Connector type - SMA.
It is unacceptable to place the antenna inside a metal box or in close proximity to metal structures.
POWER ADAPTER
The system delivery set includes a power supply unit for connecting the controller to the 220V network.
Input voltage: ~200V... 240V
Output voltage: 18V... 21V
Load current: up to 300mA
Operation temperature of the built-in thermal fuse: +1350С
To avoid overheating and subsequent irreversible tripping of the thermal fuse, it is necessary to ensure free air flow to the power supply.
BACKUP BATTERY 12V
The backup battery is connected to the controller through a specially designed for this 
nest.
Any lead-acid battery with a voltage of 12V and a capacity of up to 7.2A/h can be used as a backup battery. Such batteries are traditionally used in security systems and uninterruptible power supplies for personal computers.
If a battery with a much higher capacity is to be used (e.g. a car battery), it must be fully charged before connecting to the controller.
REMOTE DIGITAL THERMAL SENSORS
Remote digital temperature sensors operate in the range from -550С to +1250С with an accuracy of ±0.50С. The measured temperature values are sent to the controller in the form of a digital code. 
Temperature sensors are connected to the controller via the connector for the Touch Memory electronic key reader.
Each temperature sensor is completed with a 10m cable for connection to the controller.
The temperature sensor is not sealed and is not intended to be immersed in liquid.
If it is necessary to measure the temperature of the heat carrier in the pipe, it is recommended to tie the temperature sensor to the pipe with a heat-insulating tape. The length of the bandaged part of the pipe is 15-20 cm. When metal pipe to prevent damage to the sensor by stray currents, it is necessary to lay a layer of heat-resistant dielectric at least 5 mm thick between the sensor and the pipe.
Remote digital temperature sensors operate in the range from -55C to +125C with an accuracy of ±0.50C. The measured temperature values are sent to the controller in the form of a digital code. Temperature sensors are connected to the controller via the connector for the Touch Memory electronic key reader. Each temperature sensor is completed with a 10m cable for connection to the controller. The temperature sensor is not sealed and is not intended to be immersed in liquid. If it is necessary to measure the temperature of the heat carrier in the pipe, it is recommended to tie the temperature sensor to the pipe with a heat-insulating tape. The length of the bandaged part of the pipe is 15-20 cm. In the case of a metal pipe, to prevent damage to the sensor by stray currents, it is necessary to lay a layer of heat-resistant dielectric at least 5 mm thick between the sensor and the pipe.
EXPANSION UNITS
Additional expansion blocks allow you to increase the number of control zones and relays for controlling actuators.
The expansion units are connected to the controller via the connector for the Touch Memory electronic key reader.
The number of control zones (entrances) - 12.
The number of built-in relays is 4.
The maximum distance of the expansion unit from the controller is 100m.
The maximum number of expansion units in the system is 3
Each expansion unit is supplied with a 10m connection cable to the controller. The connection procedure and unit control commands are described in the operating manual of the extension unit.
TOUCH MEMORY KEY READER
The Touch Memory electronic key reader does not contain any key identification schemes.
The reader is completed with a 10m cable for connection to the controller. Up to three readers can be installed in the system.
MASTER KEY TOUCH MEMORY
The Touch Memory master key is used to register additional dongles. 
The master key can be used to arm and disarm the system, but it is recommended to use additionally registered keys for this.
The master key is hard-wired to a specific instance of the processor installed in the KSITAL GSM controller.
Restoring a lost master key is possible only at a service center and requires a complete reprogramming of the controller.
TOUCH MEMORY KEYS
Together with the KSITAL GSM controller, electronic keys DS1990A manufactured by Dallas Semiconductor or compatible are used. 
The keys are used to arm and disarm the system (see the "Mode Control" section).
Up to 6 Touch Memory electronic keys (except for the master key) can be registered in the system.
During the registration of an electronic key, its indelible code is stored in the controller's memory, which makes it possible to register the same key in several access control devices.
DETECTORS, SENSORS
The type of sensors used and their installation locations are selected based on the individual characteristics of the object. As detectors for operation in conjunction with the KSITAL GSM system, any sensors that, when triggered, can break or close the circuit, can be used. 
It is possible to connect sensors with "open collector" type output with admissible current switching over 2mA.
For easy connection of sensors requiring an external voltage source, +12V voltage is provided at the controller terminals.
The total current consumed by the sensors from the +12V controller terminals must not exceed 160mA.
If more current is needed, a separate power supply for the sensors should be used. It is desirable that the additional power supply be with its own backup battery.
EXECUTIVE DEVICES
Up to three actuators can be connected to the system at the same time. These can be: a siren, a heater, water or gas supply valves or a control system for heating, air conditioning, ventilation, irrigation, sauna, lighting, etc.
Control of these devices is possible both automatically using the controller program, and forcibly using SMS commands sent from your cell phone.
Connecting powerful electrical appliances (more than 200 watts), electric motors is made through intermediate relays (contactors) of the appropriate power.
REMOTE MICROPHONE
Microphones of this type have a built-in amplifier and three wires for connection. Microphones of the MKU and SHOROH series can be cited as an example. These microphones are similar in characteristics, but differ in design. In practice, the MKU series showed slightly better shielding and, as a result, higher noise immunity.
TERMINAL "CONTROL"
Depending on the contents of the entry in the 51st cell of the telephone directory on the SIM card, the "Control" terminal can be used as:
Analog input to measure the voltage applied to this terminal in the range from 0 to 12V;
an input that controls the arming / disarming of the system from control by applying a voltage of 12V to it (+12V - the system is under control, 0V - control is removed). This allows you to use remote controls and security panels from third-party manufacturers to control the system;
open collector output. Allows you to control the load up to 100mA at voltage up to 15V. To control a more powerful load, an intermediate relay should be used.
GENERAL INFORMATION AND BASIC PARAMETERS
Cellular control system for heating equipment KSITAL GSM-4T
is intended for notification via a cellular communication channel about the failure of the heating
equipment and remotely control it using a cell phone.
In addition to controlling heating equipment, the KSITAL GSM-4T system has
additional options for notification via SMS and voice dialing about
triggering of various sensors connected to the controller inputs. It can be
motion, vibration, glass breaking, smoke, gas leakage, flooding sensors,
pressure, or just a doorbell. The message text for each input can be
changed in accordance with the purpose of the sensor.
SMS can be duplicated by a voice message «
Anxiety!".
The system allows you to use «
panic buttons" to alert you to an attack or
emergency.
Messages are sent sequentially according to a pre-recorded list
phones.
Upon receipt of an SMS message with a control command, the controller can turn on
or turn off any of the three relays built into it. This allows you to remotely
control various devices such as heating, sauna, pumps,
lighting, etc. from a cell phone.
One built-in and up to five remote temperature sensors provide continuous measurement
room temperature. The system collects data from all connected temperature sensors
and sends them in a report as a table.
When the temperature in the room goes beyond the specified range, an SMS message about
are sent to cell phones, the numbers of which are previously entered in
memory.
The system has a mode of automatic maintenance of the temperature in the room, controlling
heating system using the built-in relay. Stabilization temperature value
is set by an SMS command from a remote cell phone.
Can be easily connected to the controller: external status indicator «
on the
control", for example, a street light annunciator, or a control panel
additional alarm system.
If there is a possibility of disconnection at the 220V voltage object, then it is necessary
use a 12V backup battery that will be charged by the controller as
need.
With a backup battery, the system remains fully operational for
loss time 220V, informs about the loss / appearance of voltage and discharge
backup battery.
There are two SIM-card readers installed on the controller board, the main one and the backup one.
operator. The system will automatically switch to a backup operator in case of network loss
the main operator or failures when sending SMS through it.
Having two systems configured as «
partners”, allows you to timely fix
problems with the cellular network or the use of radio signal jamming.
The possibility of sound control of the room with the help of an additional
external microphone.
The system is intended for installation inside a controlled object and is designed for
round-the-clock operation at temperatures from -250C to +500C.
The power consumed by the system from the AC mains is not more than 10W.
Number of built-in relays - 3.
Number of control zones (
inputs) - 8.
The maximum number of phone numbers for sending SMS messages is 10.
Maximum number of telephone numbers for dialing with a voice message
«
Anxiety!" - ten.
Overall dimensions of the controller - 15 x 11 x 4 cm.
Package size - 25 x 16 x 6 cm.
Weight with packaging - 1250 g.
Completeness:
- Controller" KSITAL GSM-T"
- Built-in GSM modem
- Power adapter 220V / 21V (minus in the center)
- Touch Memory electronic key reader with 10m connection cable to the controller
- Touch Memory master key used to register electronic keys
- Backup battery cord
- Remote digital temperature sensor with a 10m cable for connection to the controller (2 pcs.)
- GSM antenna
Boiler control
system "KSITAL" with a reasonable price and ease of installation, it has a wide range of features:
- Built-in GSM module
- 10 phone numbers for sending SMS
- 10 phone numbers to dial with voice message
- from 4 to 12 control zones for connecting signal loops with sensors
- 3 built-in relays 5A / 220V for equipment control
- built-in temperature sensor for measuring and transmitting room temperature
- the ability to install additional 6 Touch Memory keys, in addition to the master key
- the ability to listen to the room with an external microphone
- possibility of user programming long (up to 60 characters) SMS corresponding to triggering of control zones
- the ability to send SMS about the control and removal from control
- sending SMS in case of a critical drop in room temperature
- function of stabilizing the temperature in the room by remote setting
- uninterruptible power supply function, control of charging of the backup 12V battery, sending SMS in case of loss of 220V and critical discharge of the backup battery
- panic button function that allows sending alarm SMS when the system is uncontrolled
- automatic daily report (and also on request) on the health of the system
- setting the system for control both with the help of Touch Memory keys and with the help of SMS
- diagnostics of malfunction of alarm loops (breaks, short circuits) during control
- 12V power supply of the connected sensors directly from the controller (maintained when 220V is lost)
- temperature range from -25С to +50С (when equipped with a corresponding SIM-card)
GSM boiler control |
|
| Cellular boiler and heating equipment control system KSITAL GSM-4T GSM-8T GSM-12T |
|
|
By using gsm alarm and control - the possibility of automatic boiler control or an external heater from the built-in temperature sensor. GSM controller is intended for notification via a cellular communication channel about the failure of heating equipment and remote control of it using a cellular gsm phone. The built-in analog temperature sensor and up to 5 digital external sensors continuously measure the temperature. When the room temperature drops, the system sends SMS messages about this to cell phones, the numbers of which are previously stored in memory. In case of loss of 220V voltage in the controlled room, the corresponding SMS is also sent. The GSM controller for controlling the boiler and heating equipment uses a built-in GSM module. The cellular alarm system allows you to remotely start heating equipment by SMS command from a remote cell phone. In addition to controlling the boiler and heating equipment, the KSITAL-GSM-T system has additional capabilities for notifying via SMS about the operation of various sensors connected to the controller inputs. |
|
GSM Guard (for Windows)
- designed for automated monitoring of remote objects and organizationsremote control for centralized monitoring of objects(monitoring station), equipped with GSM - control and management systems.
iKsytal program (for iOS, for Android)
THERMICS-GSM(for Android)
- designed to improve the usability of the GSM control system for heating equipment Ksital GSM-4T.
Installed in smartphones with operating system Android.
The program allows you to control the heating boiler, lighting, control the temperature in the heating system and the room, turn on any additional device, arm and disarm the object, receive alarm messages and much more. Allows you to set your own names for temperature sensors and output relays.
