transcript
1 CELLULAR CONTROL SYSTEM FOR HEATING EQUIPMENT KSITAL GSM-T OPERATION MANUAL 1
2 1. Purpose and principle of operation The KSITAL GSM-T cellular control system for heating equipment is designed to notify via a cellular communication channel about the failure of heating equipment and remote control them with a cell phone. The built-in temperature sensor continuously measures the temperature in the heated room. When the room temperature drops, SMS messages about this are sent to cell phones, the numbers of which are previously stored in memory. The system has a mode of automatic maintenance of the temperature in the room, controlling the heating system using a built-in relay. The stabilization temperature value is set by an SMS command from a remote cell phone. In case of loss of 220V voltage in the controlled room, a corresponding SMS is sent. When an SMS-message is received with a request for a certain format, an SMS is sent to the cell phone connected to the system with information about the temperature in the room and the presence of 220V voltage. The system allows remote control additional equipment by SMS command from a remote cell phone. The system monitors the status backup battery and cell phone battery, maintaining their charge at 100%. In addition to monitoring heating equipment, the KSITAL GSM-T system has additional capabilities for notifying via SMS and voice dialing about the operation of various sensors connected to the controller inputs (see the Additional Features of KSITAL GSM-T section). 2. Composition of the control system and technical parameters The KSITAL GSM-T heating equipment control system includes: KSITAL GSM-T controller Cell phone of one of the models: Siemens S25, C35, M35, S35, C45, ME45, S45 (supplied separately) Adapter power supply included in the 220V network and a power controller constant voltage 21V Backup battery 12V The system is designed for installation inside a monitored facility and is designed for round-the-clock operation at temperatures from 0 0 C to C. The system remains operational at mains voltage from 160V to 240V. Recharging the backup battery is possible at a mains voltage of at least 200V. 2
3 Power consumed by the system from the network alternating current, not more than 10W. To control the actuators, normally open or closed relay contacts with a maximum current of 5A and an AC voltage of 220V are used. Number of relays executive devices- 3. The maximum number of phone numbers in the list to which SMS messages are sent is 10. 3
4 3. Installation of the system If only the basic functions of KSITAL GSM-T are used, then the inputs of additional control zones are left unused, shunted with 3.6 kOhm resistors, as it was during delivery. 3.1. Choice of the installation site The installation site of the controller is selected from the following considerations: the air temperature at the installation site should not fall below 0 0 С and should reflect the typical temperature in the room; moisture on the controller, cell phone and power adapter is excluded; should be near electric socket 220V; at the location of the controller, there must be a sure reception by the cell phone of the signal from the base station, which is controlled by the indicator of the cell phone. The controller is mounted on the wall using self-tapping screws for the mounting ears of the case. 3.2 Connecting a cell phone to the controller Insert an activated SIM card with a positive balance into the cell phone. Turn on your cell phone and make sure it works by sending and receiving test SMS from it. Delete all SMS from the SIM card. Make sure that the cells with numbers from 10 to 29 are free from entries in the phone book, because. these entries will be erased when the system is initialized. Connect the flex cable from the pocket of the controller to the socket on the bottom of the cell phone and drop the phone into the pocket. Insert the plug of the power adapter into the controller and the adapter into a 220V socket. four
5 3.3 Connecting the backup battery When connecting the backup battery for the first time, it must be charged beforehand, as When a deeply discharged battery is connected, the fuse located on the controller board may trip due to excessive starting charging current. The battery is connected to the controller using the connector included in the delivery set (+ is connected to the external contact, and - to the internal). The controller provides efficient charging of the battery with a capacity of not more than 7Ah. 3.4.Creating a phone list for sending SMS If there is no phone number in the 10th cell of the SIM card phone book, then in a few seconds after turning on the power, the controller will generate a template of the list of phones to which SMS messages will be sent. The pattern looks like: 5
6 The list consists of the main phone number, located in cell 10, 9 additional ones for sending SMS and 10 for dialing with a voice message Alarm! (See section Additional Features of KSITAL GSM-T). It is necessary to edit this list by entering the numbers you need in the international format, i.e. for Russian Federation the number must start with +7 and consist of 11 digits (the format of numbers for voice dialing can be arbitrary). For example, an MTS cell phone number may look like, a cell phone number with a direct Moscow number or a MGTS phone number (for voice dialing) as Add the number of phone numbers you need to the list, and at least the main phone number must be filled in 00SMS. The system will not start unless it finds the main phone number and will notify you by playing music on the cell phone. Reader indicator electronic keys will glow red continuously. Therefore, since Initially, after downloading the template, the main phone number is not filled in, then, after hearing the loss, fill in this number, turn off the power supply of the controller and turn it on again after a few seconds, thereby restarting the system. The controller will issue further messages in the form of SMS to the main phone number. 3.5.Loading default settings If all SMS messages have been deleted from the SIM card, the controller will load the default settings into the SIM card memory during initial startup. They are contained in SMS with the name Nastroyki in the section with outgoing unsent SMS. SMS settings looks like: 6
7 3.6.Connecting actuators Up to 3 actuators can be connected to the controller. Connect actuating devices to the relay outputs of the controller following the switching options below. If it is necessary to control powerful devices, then intermediate relays of the appropriate type should be used. 4. System operation 4.1.Event notification :-system KSYTAL- Vnimanie! Temperature nije +15C. The message will indicate the value of the temperature level, the fall below which caused the mailing. When the 220V voltage fails, the system switches to power from the backup battery. After 10 seconds, if the voltage is not restored, an SMS message will be sent: -system KSYTAL- Vnimanie! Propalo naprjagenie 220V. The message about the critical discharge of the backup battery looks like: -system KSYTAL-Akkumulator razryagen. The message is sent when the backup battery voltage drops to 11V. From now on, the correct operation of the system is not guaranteed. 7
8 4.2. Notification on request In order to receive information about the presence of 220V voltage and the temperature in the controlled room, send an SMS message with a request of the required format to the cell phone connected to the controller (see the Request command format section). The response message will be as follows: -system KSYTAL-Temperatura +22C Vnimanie! Propalo naprjagenie 220V. Or, for example, -system KSYTAL-Temperatura +17C Naprjagenie norma. 4.3.Daily report A report, similar to the one sent on request, can be sent automatically once a day, if it is specified in the settings (see the Programming section). 4.4.Operation in the temperature stabilization mode The air temperature in the room, which must be maintained, is set from a remote cell phone (see the Control command format section). If the room temperature falls below the set value, the controller turns on the heating boiler via relay 2. When the temperature exceeds the set temperature by 2 0 C, the boiler will be switched off. It will turn on again when the room temperature drops below the set temperature. Thus, the controller will maintain the room temperature within two degrees of the set temperature. When first turned on, the stabilization temperature value is equal to 0 0 С. 5. Charging the batteries Charging the backup battery from the mains adapter is activated if the voltage on the battery drops below 13.6V. The charge level of the backup battery is not guaranteed when the mains voltage is below 200V or when using a non-standard adapter. Cell phone battery charging starts when the battery level falls below 80%. Charging current 100mA. Charging takes place from the mains adapter, and in the absence of voltage 220V from a backup battery. Cell phone charging does not turn on when the voltage on the backup battery drops below 11V. 6. Programming The user has the ability to change the mailing list, change system settings, edit the text of sent commands. eight
9 Changing the system settings is done by editing the SMS text with settings generated by the controller during initial power-up. The new settings will only become active after restarting the controller! Each line in the settings sets one or another parameter in accordance with the rules described below. 6.1.Changing the SMS distribution list The SMS distribution list is located in the phone book of the SIM card. The list contains from 1 to 10 phone numbers. The main phone, in addition to messages about changes in the status of controlled areas, receives some service messages. To add, remove, or change phone numbers in a mailing list, you must edit the entries in the corresponding cells in the phone book. It is important that phone numbers are in international format. Otherwise, the mailing will not be made to the incorrectly recorded number. Accordingly, to exclude a number from the mailing list, you can simply remove the + sign before the number or, for example, write zeros instead of the number: Changing the header of sent SMS The line in the -system KSYTAL- settings sets the initial line in all SMS sent by the controller. The text between hyphens will be used as a header in sent SMS. Changes in accordance with the rules for editing the SMS text. The number of characters in the text is not more than 16. Examples of specifying this line: -Dacha- ; -Office 1- ; -Garage- ; -Jukovka PIN-code programming The line in the PIN= settings specifies the PIN-code that should accompany the commands received by the controller in the form of SMS from any cell phone or the Internet. The PIN code must contain from 1 to 5 any numbers or letters, except for spaces and equal signs =. Examples of setting this line: PIN=12321, PIN=tam, PIN=fr16, PIN=1s2d. Default value: PIN=
10 6.4.Programming the daily report The line in the settings Otchet= sets the need for an automatic daily report on the unit's health. Report=0 means do not send a daily report. Report=1 - send a daily report. The first report will be sent one day after the last restart of the controller. The report time will be changed if a status command is sent to the cell phone connected to the controller: How dela? xxxxx, where xxxxx is replaced by a PIN. Subsequent daily reports will be sent at the same time of day. Default value: Otchet= Programming the temperature stabilization mode The line in the Nagrev= settings specifies whether relay 2 should be automatically turned on if the room temperature drops below the set one. Nagrev=0 means that relay 2 turns on and off according to commands received in the form of SMS. Nagrev=1 means that relay 2 will turn on when the room temperature falls below the set temperature. Default value: Nagrev= Programming advanced settings The remaining settings can only be changed if advanced features are used. The description of these settings is given in the Additional Features of KSITAL GSM-T section. ten
11 7.Format of control commands The controller analyzes all incoming SMS. To avoid overflowing the SIM card memory, all incoming SMS messages are deleted after decryption. If the received SMS contains a command of the required format and the correct PIN code, then the command is executed. 7.1.Format of actuator control commands To turn on the actuator connected to relay 1, it is necessary to send SMS Vkluchit relay 1 xxxxx to the cell phone connected to the controller, where xxxxx is replaced by a PIN code. system (default 00000). The highlighted characters are required. A space is also required before the relay number and before the PIN code. The rest of the characters can be arbitrary. It is assumed that SMS with control commands are prepared in advance and the user simply sends the required SMS if necessary. At the same time, it is convenient to edit the command in such a way that it is clear from the text what will be included. For example, the command can be sent in one of the options: Vkluchit nasos or Vkl osveshenie or Vkluchit saunu or Vkl To turn on relay 2 or 3, the numbers of these relays are indicated in the corresponding position: Vkluchit relay or Vkluchit rele The command to turn off the relay has a similar format (for example, relay 1): Otkluchit rele Possible variants of this command: Otkluchit projektor or Otkluchit saunu or Otkl
12 7.2. Request command format If you need to know the temperature and the presence of 220V voltage in the controlled room, you should send SMS to the cell phone connected to the controller: How is it? xxxxx, where xxxxx is replaced by a PIN. (default 00000) Emphasized characters are required. Is there also a required space between the ? and PIN code. The type of response SMS is described in the Notification on request section. 7.3.Temperature command format To set lower threshold temperature in the room, which must be maintained by KSITAL GSM-T, it is necessary to send an SMS to the cell phone connected to the controller: Temperatura = tt xxxxx, where tt is a two-digit temperature value, and xxxxx is a PIN code. (default 00000) Emphasized characters are required. A space is also required between the temperature value and the PIN code. Temperature command example: Temperatura = or Tem=
13 8. Additional features of KSITAL GSM-T This section should be studied if it is necessary to use the controller inputs to connect additional sensors. With the help of short SMS messages, KSITAL GSM-T signals the operation of various sensors at the facility, such as thermal sensors, magnetic contacts, infrared, ultrasonic or microwave volumetric motion sensors, gas leakage, smoke, water flooding sensors and others. SMS can be duplicated by the voice message Alarm!. Up to 4 control zones can be allocated at the facility. Each of the zones can be represented by any required number of sensors connected in one alarm loop. Messages are sent sequentially to a pre-recorded list of phones. Zone 4 allows the connection of panic buttons for notification of an attack. The removal and setting of zones for control are carried out using electronic keys of the Touch Memory type. To recognize the key, it is necessary to touch the contact area of the reader connected to the controller with it. Setting for control can also be done remotely, using the appropriate SMS command. It is possible to listen to the room using an additional external microphone. 8.1.Additional equipment To use the additional features of KSITAL GSM-T, the system must be equipped with sensors, Touch Memory electronic keys and an electronic key reader. The sensors connected to the controller inputs must be divided into groups. Each group provides control of one zone. When any sensor is triggered, KSITAL GSM-T sends an SMS indicating the triggered zone. Sensors of one zone are connected, as a rule, in series. The zone is considered triggered when the total loop resistance deviates by 25% from the resistance measured during control. The number of zones - 4. The response time of the controller to the operation of the sensors is not more than 0.5 seconds. The delay for sending SMS when zone 1 sensors are triggered (usually connected to the front door) is programmable in the range from 1 to 99 seconds. 13 must be used to connect sensors to the controller.
14 unshielded 2 or 4-core cable with a wire cross section of at least 0.22 mm 2. To connect the electronic key reader to the controller, an unshielded 4-core cable with a wire cross section of at least 0.15 mm over 50 meters. The number of master keys is 1. The number of simultaneously registered electronic keys (including the master key) is not more than Connecting sensors to the controller As a rule, sensors with normally closed dry contact output are used. In this case, in series with the chain of sensors, it is necessary to install a resistor of such a value that the total resistance of the loop is in the range: 2 5 k. Sensors that control the entrance door or the room behind the entrance door (entrance hall) must be connected to zone 1, which has a programmable response delay. Mount the sensors in accordance with the instructions attached to them, combine them into zones and connect them to the controller terminals in accordance with the connection diagrams: for sensors that do not require a power source (magnetic contact, electric contact detectors, etc.); for sensors using an external power source (infrared, microwave, smoke detectors, etc.). fourteen
15 Each zone is represented by a group of three terminals. The purpose of the terminals in each group (from left to right): 1 common wire, 2 - combined signal wire from the sensors, 3 positive wire for +12V sensors power supply. If less than 4 zones are used, then 3.6 kΩ resistors must be connected to the terminal blocks of unused zones, as it was when the controller was delivered. After installation, check the total resistance of each loop with a tester. 8.3 Mounting the key reader and connecting it to the controller Mount the electronic key reader near the entrance door inside the premises. Connect the reader to the controller using the cable included in the kit. If KSITAL GSM-T is used as a security alarm, it is advisable to lay the cable covertly so as not to unmask the controller Registration of Touch Memory electronic keys The last 6 lines in the settings determine the registration of Touch Memory electronic keys. Initially, no electronic key (except for the master key) was registered in the system. To be able to remove and put the inputs under control, you must register at least one key. fifteen
16 Registration of a new key is possible only if there is a master key, the code of which is the password for the registration procedure. Despite the fact that the master key allows you to remove and put the inputs under control, it is recommended to store it separately and use it only for registering additional keys, because. If you lose it, you will lose the opportunity to register new keys. To register key 1, you first need to edit the corresponding line in the SMS with settings as follows: 1kluch=1. Then restart the controller. When starting, having found in the settings the need to register key 1, the controller will go into the waiting mode for entering the master key code (the indicator on the electronic key reader blinks evenly in green). Not later than 1 minute it is necessary to attach a master key to the contact of the reader. At the moment of touching, the cell phone will emit two short beeps. If the code of the attached key matches the code of the master key, then the controller allows the registration of a new electronic key (the indicator on the electronic key reader glows green evenly). After that, it is necessary to attach a registered key to the reader contact. At the moment of touching, the cell phone will emit a short beep and an SMS message will be sent to the main phone: Vnimanie! Installed novyi kluch Modes for monitoring sensors and registering electronic keys KSITAL GSM-T has 5 additional control modes: registration and deregistration of electronic keys; control removed; putting under control; on control; withdrawal from control. The number of the mode in which the controller is located is stored in non-volatile memory and is remembered in the event of a power failure. When the power is restored later, the mode that was before the power failure is restored. For example, if KSITAL GSM-T was not equipped with a backup battery and was in input control mode, then after a power failure of 220V and its subsequent restoration, it will continue to work in the same mode. If there is a backup battery, a power failure of 220V for more than 10 seconds in any mode causes a message to be sent to the main phone: Vnimanie! Propalo naprjagenie 220V. 16
17 8.5.1. Mode of registration and deregistration of electronic keys When the controller is powered on, it checks whether the number and numbers of keys specified in the settings correspond to those stored in the non-volatile memory of the controller. If no differences are found, the controller switches to the control disabled mode. Otherwise, the procedure for registering or deregistering a new key is activated (see the Registration of Touch Memory electronic keys section). Control mode disabled In the control mode disabled, the controller provides power to the sensors connected to it, but does not respond to their activation. The exception is panic buttons connected to zone 4 (see Programming additional features). The indicator on the electronic key reader flashes green evenly. SMS incoming to the cell phone is monitored. If they contain commands of the appropriate format, then these commands are executed. The system monitors the charge level of the cell phone battery and the backup battery and, if necessary, activates their recharging. The system polls the electronic key reader. When the reader is touched with one of the registered keys, the controller switches to the control setting mode Control setting mode The control setting mode is indicated by a continuous green glow with rare yellow flashes of the indicator on the electronic key reader. This starts a timer for 90 seconds. If KSITAL GSM-T is used as a burglar alarm, then during this time it is necessary to leave the controlled premises. After 90 seconds, the controller measures the resistance of signal loops and saves these values in non-volatile memory. These values are the reference ones, the current loop resistances will be compared with them in the control mode. If the values of the reference resistances are outside the allowable range of 2 5 kΩ, then a warning will be sent to the main phone: Vnimanie! Nedopustimoe soprotivlenie Shleifa. In this case, it is necessary to find and eliminate the cause of a significant change in the resistance of the loop, since this indicates a possibly poor contact in the signal loop and can lead to false alarms.
18 operations. In the event of a break or short circuit loop, an SMS will also be sent about the activation of the controlled zone, indicating its number. Then the system goes into control mode. If necessary, you can program in the settings to send SMS systema na kontrole to the main phone every time the system is put on control (see Section Setting the mode of information about the removal and putting on control) Control mode Control mode is indicated by short yellow flashes of the indicator on the electronic key reader. In this mode, KSITAL GSM-T recharges the backup battery and the cell phone battery as needed, executes the commands contained in incoming SMS, reports a power failure of 220V and the discharge of the backup battery, and controls the resistance of signal loops with sensors. The deviation of the resistance of any loop from that measured during setting up for control by more than 25% is considered as triggering the controlled zone. A typical situation is when each sensor works as a trip and all sensors of one zone are connected in series. In this case, when any sensor is triggered, the total resistance of the loop becomes infinitely large, which means that the zone is triggered. A message about this is sent to all phones included in the mailing list. If the settings are programmed to turn on the siren when triggered, then after sending an SMS, relay 3 is turned on for 2 minutes, causing the actuating device (siren) connected to this relay to be triggered. After the 4-fold triggering of the sensors of any zone and the distribution of the corresponding SMS, the zone is disconnected from control and subsequent triggering of the sensors of this zone does not lead to SMS distribution. This zone will be switched on only during the subsequent control. Disarming mode The disarming mode is activated when zone 1 is violated (the indicator on the electronic key reader flashes red). After recognizing the code of the electronic key attached to the reader, KSITAL GSM-T switches to the control disabled mode, which is accompanied by two short beeps and a change in the indicator light. If KSITAL GSM-T is used as a burglar alarm, then the sensors that control the front door and hallway are connected to zone 1, and when they are triggered, SMS messages are sent after a programmable delay. Over time 18
19 delay, it is necessary to remove KSITAL GSM-T from control with a pre-registered electronic key. If necessary, it can be programmed to send a Control systemy snjat message to the main phone upon disarming (see Section Setting the Disarm and Control Information Mode). 8.6.Programming additional features Programming the 1st zone activation delay The line in the Zaderjka= settings defines the delay time between the activation of zone 1 sensors and the sending of an SMS about zone activation. During this time, it is necessary to remove KSITAL GSM-T from control by attaching the registered electronic key to the reader. To change the delay time, you need to edit the two digits after the = sign. Examples of setting this line: Zaderjka=05, Zaderjka=15, Zaderjka=99. The delay time can vary from 01 seconds to 99 seconds. Default value: Zaderjka = Setting the mode of information about disarming and arming the system The line in the RI= settings sets the mode of information about disarming and arming the system. RI=0 means do not send SMS about the removal of the system control; RI=1 means to send an SMS to the main phone about the control; RI=2 means to send an SMS to the main phone about removal from control; RI=3 means to send an SMS to the main phone about removal from control and about putting on control. Default value: RI= Programming automatic start sirens The line in the Syrena= settings specifies whether the siren should be turned on when the controlled zone is violated. Syrena=0 means do not turn on relay 3 and actuators connected to it in case of violation of controlled zones. Syrena=1 means to automatically turn on relay 3 and actuators connected to it for 2 minutes in case of violation of controlled zones. Default value: Sirena=0. 19
20 8.6.4 Programming the panic button The line in the Knopka= settings sets the possibility of using the 4th zone for connecting panic buttons. Knopka=0 means that the 4th zone is used in normal mode, i.e. in the state removed from control, the system does not react to the triggering of sensors connected to this zone. Knopka=1 means that the 4th zone is controlled and in the uncontrolled state of the system. This allows you to connect panic buttons to this zone. Clicking on any of them in the unmonitored state of the system will send SMS: Alarm! Attack. Default value: Knopka= Editing the list of registered electronic keys KSITAL GSM-T allows you to selectively register or de-register any of the 6 electronic keys. line in settings
21 are mandatory. There must be no spaces before the PIN and after the zone number. Command example: 2(Trevoga! Utechka gaza!) 00000 or 3(Vnimanie! Nedopustimo vysokoe davlenie vody v truboprovode!) Remote arming command format KSITAL GSM-T can be controlled by sending an SMS to a cell phone connected to the controller with the command Install control xxxxx, where instead of xxxxx is the system PIN (00000 by default). The highlighted characters are required. A space before the PIN is also required. Command example: Settanovit control or Ust control Remote microphone remote activation command format To remotely turn on the remote microphone, send SMS to the cell phone connected to the controller: Mikrofon xxxxx, where instead of xxxxx is the system PIN code (00000 by default). The highlighted characters are required. A space is also required between n and the PIN. After the command is recognized, the controller will make a call back to the main phone 00 SMS with the external microphone turned on. The microphone will be turned off automatically after disconnection at the initiative of the owner of the main phone 00 SMS. 9. Indication of modes and system messages 21
22 Important notes The KSITAL GSM-T control system uses insignificant traffic, so it is preferable to use a tariff without a monthly fee, for example Super Jeans MTS. However, it must be remembered that this tariff does not allow for the use of paid services within 180 days. Control the state of the account and do not allow it to be blocked. You can use a 12V uninterruptible power supply instead of a backup battery and AC adapter. But in this case, the information about the loss of 220V voltage becomes unavailable to the controller and, accordingly, SMS about the loss of voltage is not sent. If necessary, you can use the mobile phone connected to the controller to make regular calls. The system settings and the mailing list are stored on the SIM card. Therefore, when changing the SIM card, it is necessary to re-create the list of phones and edit the settings as during the initial launch. On the contrary, this will not be required when replacing a mobile phone if you replace the SIM card with settings from the old phone into it. If you delete the main phone number in the address book, recorded in the 10th cell, then the next time you restart the distribution list will be replaced by empty templates. To restore the default settings, you must erase all SMS on the SIM card of the cell phone connected to the controller, and then restart the controller by turning the power off and then on again. For greater reliability and speed of SMS delivery, try to use the same mobile operator to send and receive SMS. If you need to use the services of different operators, first make sure that there are appropriate agreements between them. It is also useful to check the practically stable delivery and the absence of distortions in messages. When writing SMS commands, you must use the Latin text encoding. Otherwise, the SMS you sent may not be recognized by the controller as an executable command. 22
23 Contents 1. Purpose and principle of operation Composition of the control system and technical parameters Mounting the system Selecting the installation location Connecting a cell phone to the controller Connecting a backup battery Forming a list of phones for sending SMS Loading default settings Connecting executive devices 7 4. System operation Notification by event Notification by event request Daily report Working in temperature stabilization mode 8 5. Charging batteries Programming Changing the SMS mailing list Changing the header of sent SMS Programming the PIN code Programming the daily report Programming the temperature stabilization mode Programming additional settings 10 7. Format of control commands Format of commands for controlling actuators Temperature setting command format 12 8.Additional features of KSITAL GSM-T it to the controller Registration of electronic keys Touch Memory Modes of control of sensors and registration of electronic keys Mode of registration and deregistration of electronic keys Control mode removed Control setting mode Control mode 18 23
24 8.5.5. Disarming mode Programming additional features Programming delay of operation of the 1st zone Setting the mode of information about disarming and arming Programming the automatic activation of the siren Programming the panic button Editing the list of registered electronic keys Programming the text of SMS messages Remote arming command format remote control Format of remote microphone activation command Indication of modes and system messages 21 Important notes
HARDWARE EXPANSION UNIT FOR USE IN JOINT WITH KSITAL GSM SYSTEM KSITAL V0R8 OPERATION MANUAL 2 3 GENERAL INFORMATION AND MAIN PARAMETERS Block hardware expansion Xital V0R8 (further
HARDWARE EXPANSION UNIT FOR USE IN JOINT WITH KSITAL GSM SYSTEM KSITAL V8R4 OPERATION MANUAL 2 GENERAL INFORMATION AND BASIC PARAMETERS Ksital V8R4 hardware expansion unit (hereinafter
CELLULAR WARNING AND CONTROL SYSTEM KSITAL GSM-8 OPERATION MANUAL GENERAL INFORMATION AND BASIC PARAMETERS Cellular notification system "KSITAL GSM-8" is designed for remote control
CELLULAR CONTROL SYSTEM FOR HEATING EQUIPMENT KSITAL GSM-12T OPERATION MANUAL GENERAL INFORMATION AND BASIC PARAMETERS
CELLULAR HEATING EQUIPMENT CONTROL SYSTEM GALAN-GSM OPERATION MANUAL GENERAL INFORMATION AND BASIC PARAMETERS
Research and Production Enterprise POTENTIAL GSM - LAIKA Control panel device User's manual and passport
CELLULAR CONTROL SYSTEM FOR HEATING EQUIPMENT KSITAL GSM-4T OPERATING MANUAL GENERAL INFORMATION AND BASIC PARAMETERS
Instructions for GSM operation- alarm "Dachnik - Informer" Before using the device, please read this manual Inside the GSM alarm "Dachnik" there is a high
EMERGENCY CELLULAR SYSTEM FOR CONTROL OF HEATING EQUIPMENT ZIMA 911 OPERATION MANUAL 2 GENERAL INFORMATION AND BASIC PARAMETERS
User manual for use and GSM installation alarm system Mega SX-250. Removing and arming the alarm. To remove / arm the alarm, the following can be used: Electronic
SETUP OF THE AURA SYSTEM 3 INSTRUCTIONS QUICK START CONTENTS BASIC SETTINGS Step 1. Connecting the system and sensors...3 Step 2. Recording user phone numbers and setting the time...5 MANAGEMENT
Notification transmission system "MKSOV-KP v.9833" Operation manual 1. Purpose
Instructions for quick setup of devices using ONE SMS message GSM Alarm "Sentry-BOX-1MT" 3x4 Page 2 GSM Alarm "Sentry-BOX-1MT" 3x4 Set Page 5 GSM Alarm "Sentry-BOX-1M"
CELLULAR CONTROL SYSTEM FOR HEATING EQUIPMENT KSITAL GSM-4T OPERATION MANUAL 2 GENERAL INFORMATION AND BASIC PARAMETERS
ÏÎÒÅÍÖÈÀË GSM 3x5 mini Ïðèáîð ïðèåìî-êîíòðîëüíûé îõðàííûé Ðóêîâîäñòâî ïîëüçîâàòåëÿ ÍÀÇÍÀ ÅÍÈÅ Ïðèáîð ïðèåìî-êîíòðîëüíûé îõðàííûé GSM 3x5 mini,äàëåå - óñòðîéñòâî,ïðåäíàçíà åí äëÿ êîíòðîëÿ îáúåêòîâ íåäâèæèìîñòè
AT-820 8-channel GSM remote control with 2-zone GSM alarm 8-channel DTMF controller, allows you to control: arming and disarming, lighting, thermostat, garage doors,
Guide for setting up the set "For giving, house, apartment, MINI" GSM Alarms "Smart sentry-4": Remove the set of GSM Alarms "Sentry-4" from the package. The set must contain: 1. GSM device "Smart
Contents 1. Purpose...2 2. Package contents...3 3. System functionality...3 4. Installation and testing...4 5. Phone control...7 6. Security mode...10 7. Listening to the interior of the car...11
Table of contents About signaling.... 1 GSM Informer Sentry-1M... 2 GSM Informer Sentry-1MT... 4 GSM Informer Sentry-5... 6 GSM Signaling Sentry-BOX-1M... 8 GSM Signaling Sentry-1МТ... BOX-1MT... 10
Guide for setting up the set "For giving, at home, apartment, Pro" GSM Alarms "Smart sentry-4": Remove the set of GSM Alarms "Smart sentry-4" from the package. The kit must contain: 1. GSM device
Operating manual GSM alarm system VH-1800 1 Complete set 1. GSM module 1pc. 2. Wireless IR sensor 1pc. 3. Wireless magnetic contact sensor 1pc. 4. Radio channel keychain 2 pcs. 5. Block
GSM relay RK-1 OPERATING MANUAL GSM relay RK-1 (hereinafter referred to as the device) is designed to inform about the status of contact sensors and temperature sensors at remote objects, as well as to control
GSM monitoring and control system MKTU-300F Technical certificate Operating instructions St. Petersburg 1. Purpose of the device Universal GSM system- control and management "MKTU-300F" is intended
1. App installation 2. App launch and setup 3. Control menu 4. Temperature menu 5. Status menu 6. Settings menu Contents: 1. App installation To install the app
CELLULAR CONTROL SYSTEM FOR HEATING EQUIPMENT KSITAL GSM-12T OPERATION MANUAL С14.06.01 2 GENERAL INFORMATION AND MAIN PARAMETERS Cellular heating equipment control system KSITAL
SAMSON LINK CHARACTERISTICS Supply voltage ... 4-18 V (typical 4.2 V) Consumption ... 20 mA Outputs ... 1, open collector, up to 3 A Inputs ... 4 External loop integrity resistors resistance.... .
Ectostroy Manufacture and sale of GSM systems Version 2.1 Remote monitoring system Quick start guide 1 QUICK START GUIDE how to set up the EctoControl system in 4 simple steps
Independent programming of the alarm system is carried out using a cell phone! All independent settings of the security alarm profile are carried out by entering the setting information
LOCAL ACCESS CONTROL UNIT PROGRAMMING MANUAL ibc-03 Alarm Local access control unit ibc-03 is designed for access control and tamper alarm
relay remote GSM control SIMply MAX P01 series Operating manual Purpose The SIMply MAX P01 series remote control relay consists of two independent channels and is designed for
Manual for quick setup of Garage Pro set GSM Alarms "Smart Sentry-4": Remove the set of GSM Alarms "Smart Sentry-4" from the package. The set must contain: 1. GSM device "Smart Sentry-4"
CELLULAR WARNING AND CONTROL SYSTEM KSITAL GSM-4 OPERATING MANUAL 2 GENERAL INFORMATION AND BASIC PARAMETERS
GSM alarm system User manual www.signal-gsm.ru Purpose The device is intended for use in everyday life, for notification by dialing and sending SMS messages to the owner's phones. Functions
Security GSM system GSM Watchdog 838Ru. 1 GENERAL RECOMMENDATIONS FOR USING THE SYSTEM....2 2 VOICE MENU, USER FUNCTIONS....3 2.1 PROGRAMMING NUMBERS AND PIN CODE TO THE PHONEBOOK....3 2.2
A device for transmitting messages over a mobile communication channel. Instructions for programming and connection. 1. The purpose of the device and the principle of operation. The device is designed to connect to a cellular
GSM ALARM SYSTEM ALM-GSM-003 USER MANUAL Features Sleek and advanced touch keypad for easy operation; Display resolution 128x64 displays the time; Possibility
ELEMENT-1120 (E-1120) CONNECTING TWO ALARM SENSORS, A THERMAL SENSOR AND A LIGHT SIGNAL Dear user! Thank you for choosing the Element-1120 device. Highly recommended for initial
Universal handset of the GSM-intercom Ksital GSM-02 for calling panels METAKOM, VISIT, CIFRAL, ELTIS
Page 1 of 19 CONTENTS 1 Purpose mobile application Private Mobile... 3 2 Installing the Application... 4 3 Getting Started with the Application... 5 4 Registering Sites... 6 5 List of Sites... 9 6 Menu
security alarm system. Instruction 1. Introduction 2. Functions 3. Technical specifications 4. Installation 5. Basic parameters 6. Adding / removing additional sensors and key fobs 7. Programming the main
SATEL CA-6 FIRE AND SECURITY CONTROL PANEL 1 2 3 4 5 6 7 8 9 * 0 # 1 2 3 4 5 6 7 8 POWER PHONE FAILURE A ARMED B A ALARM B GENERAL DESCRIPTION AND USER MANUAL CONTENTS 1. GENERAL DESCRIPTION...
Manual for setting up the GSM Alarm "Sentry-8x8-RF-BOX" set "PROFI": Remove the GSM Alarm set "Sentry-8x8-RF-BOX" from the package. The kit must contain: 1. GSM device "Sentry 8x8-RF-BOX"
Operating instructions GSM-alarm system "Dachnik" Before using the device, please read this manual. ATTENTION! Inside the GSM-alarm "Dachnik" there is a high
Frequent user questions about the Xital GSM 4T system
What is the difference between Xital 4 and Xital 4T
The Xital 4T version comes with 2 wired temperature sensors pre-configured to work with the system. There are no such sensors in the Xital 4 version (which is why it is cheaper). Also in the "T" version, a special reader with two outputs to the thermal sensor loops is included. Messages about power failure in Xital GSM 4T are sent to all user numbers, and in Xital 4 only to the main number.
Which operator's SIM card should I choose?
The operation of the system is guaranteed for operators using 2G communication networks. Thus, for Moscow and the Moscow region, work on the TELE2 network is impossible. Choose tariffs without a monthly fee and with the cheapest SMS messages.
What heating devices can be controlled by the Xital system
Heating control is possible using almost any boiler or electric convector. The manufacturer of the device is not important, since 99% of heating devices can be connected to the Xital system.
Which xital should I choose to control the BUDERUS boiler
Any Xital with index "T", for example Xital GSM 4T which already has 2 thermal sensors.
Which xital should I choose to organize the security of a house, apartment, office or store
If you do not plan to use the heating control functions, then the Xital version without the "T" index is sufficient. Next, you need to decide on the number of security zones (rooms) and, depending on this, choose the Xital 4, 8, 12 version.
I can not do the installation of the Xital system. Can you install it in my house for me?
Yes, we do professional installation of Xital systems. Our specialists are trained by manufacturers of heating equipment, and there are corresponding certificates in the Installation section. Prices for installation work depend on the complexity of installation and the distance from Moscow and start at 5,000 rubles. For ordering installation we have a valid system of discounts.
In another store, I saw a lower price for Xital, why is it wrong with you
We sell at the official prices of the manufacturer and are the official dealers of the manufacturer. We have our own equipment selection service, technical support for our customers for the entire life of the system, warranty service, installation and repair. Compare with those companies that offer to buy Xital for 500 rubles cheaper and think about what you face in this case. the choice is yours.
Who can benefit from installing the Xital 4T system
You are the owner of suburban real estate heated by boilers, convectors and other heating devices and want to save money. Then a set of GSM control of heating equipment - Ksital GSM 4T - was created especially for you. Thanks to this system, you will save up to 30% or more on maintaining a comfortable temperature in the house.
The manufacturer has adapted the Xital GSM 4T system to the maximum for a quick start. Everything you need is already in the box. The user only needs to read the instructions and connect all the elements from the box into a single whole, and by installing the SIM card in a special slot, make the first start.
1 built-in temperature sensor and 2 external (included) allow you to immediately organize temperature control in three different areas of the room. And in the future, it is possible to expand the control zones with additional wired or wireless temperature sensors. Naturally included temperature sensors are already configured on the control panel, and additional ones can be easily connected if you follow the instructions from the instructions.
What is the cost savings with this system?
The Xital system is connected directly to the "brains" of the heating boiler and controls the heating on by its own temperature sensors. When leaving home, the user sets the minimum temperature (for example, 10 °C), and when arriving, several hours in advance, using SMS, he sets a comfortable temperature (for example, 25 °C). Thus, during the absence, the boiler does not work 90% of the time, saving gas, electricity and other fuels.
Please note that you can separately set the temperatures for day and night mode.
What boilers does the Xital 4T system work with?
This device is able to control the operation of almost any heating boilers, electric radiators and convectors. Among them are such eminent manufacturers as Buderus, BAXI, Protherm and others. Xital GSM 4T is able to control even those boilers that are not amenable to regular control methods.
Even if your house has not one, but several heating circuits, then Ksital can easily cope with this task. It will be able to separately control various circuits (underfloor heating, radiators) according to individual temperature values, and also, when an expansion unit is connected, turn on / off pumps, lights and other electrical appliances.
What else can be implemented using Xital GSM 4T
You can organize a security system and notification of emergency situations at the facility. In the event of a danger, the system will notify subscribers whose numbers are stored in the device's memory with short SMS messages and calls.
In normal operation, the system supports wired sensors, but by completing the system with the Ladoga-BRSHS expansion unit, it is possible to work with wireless sensors.
Complete set of the Xital GSM 4T system
Autonomous heating systems are widely used in modern private houses and cottages, as well as in apartments. Not only cosiness and comfort in the house, but also safety depends on their correct work.
After all, even a small breakdown of one of the nodes of heating systems can lead, at best, to the repair of equipment, and at worst, to serious damage to housing and property stored in it.
In order to be able to protect yourself from unforeseen accidents, breakdowns and emergency situations, special electronic alarms are used. One of these systems is Xital GSM 4T, used for automatic monitoring of the operation of domestic heating systems.
Functional purpose
Cellular systems Xital GSM are special electronic devices that, using the mobile network of one of the operators, can notify the owner of the house about an emergency situation that has arisen at the facility.
Also, using the same cellular connection, you can remotely control the actuators heating systems. To do this, use a mobile phone paired with Xital GSM 4T - the instructions included in the alarm package will allow you to quickly connect the phone in a few minutes.
Advantages
- In addition to monitoring the functioning of heating equipment units, Ksital GSM 4T alarms allow you to notify using SMS messages and voice dialing about the operation of sensors / sensors connected to the inputs of the Ksital 4T electronic unit. These can be motion sensors, sensors for opening windows / doors, glass breaking, sensors for the presence of gas, water, smoke, etc.
- The text in the SMS message can be individual for each of the available inputs. It adapts to the type of sensor that is connected to the corresponding input. If necessary, text messages can be duplicated by a voice call with an "Alarm" notification. Sending SMS messages is carried out to telephone numbers that are recorded in the memory of the SIM card during the time when the Xital GSM 4T is configured.
- Special service SMS messages are used to control the operation of equipment controlled by GSM alarms. They act on the controller, which turns on or off the relay system controlled by external mechanisms. For correct use by Xital GSM 4T service commands, the instruction manual describes in detail their correct spelling and functional purpose.
Specifications
| Options | Values |
| Producing country | Russia |
| Guarantee | 1 year |
| Supply voltage | 12 VDC |
| Backup power | external battery |
| Working temperature | — 25 °C…+ 50 °C |
| Number of alert numbers | 10 |
| Number of hardwired zones | 4 |
| Number of temperature sensors | 1 built-in, up to 5 remote (2 included) |
| Measured temperature | — 55 °C…+ 125 °C |
| Number of outputs | 3 (type "relay" 5A/220VAC) |
| Microphone | Remote (not included) |
| dimensions | 150×111×40 |
| The weight | 850 g |
How does the alarm work?
Xital GSM 4T systems include one built-in and 5 remote temperature sensors that perform continuous measurement temperature regime in room. The electronic unit, which is owned by the GSM alarm system Ksital, collects information from all sensors / sensors and analyzes it in accordance with a special algorithm.
If the temperature in one of the zones controlled by temperature sensors goes beyond the set limits, a danger alert will be sent to selected phone numbers. Devices of this series allow simultaneous control of 4 zones. To increase the number of controlled zones, the Ksital 12T series alarm system can be used.
To improve the fault tolerance and reliability of systems that control heating equipment and the situation at the facility, it is practiced to use 2 Xital systems, which are used as “partner devices”. For example, together with Xital 4T, Xital GSM 12T can be used - the instruction describes in detail the possibility of paired use of two alarms.
What actuators are connected?
GSM alarm system Xital GSM 4T allows you to connect up to 3 actuators. These can be sound sirens, light emitters, valves and locking mechanisms, control devices for air conditioning systems, forced ventilation, smoke removal, and so on.
To connect electrical appliances with an operating power of more than 0.2 kW, special contactors (intermediate relays) with a selected power value should be used. Otherwise, the alarm may fail - then it will be necessary to repair the Xital GSM 4T.
The control of the connected devices is carried out automatically using a microcontroller, which is equipped with the Xital GSM 4T alarm system, or through SMS service commands sent from a mobile phone.
Who can carry out the installation?
Installation of Xital GSM 4T is carried out by specially trained specialists of companies that specialize in the installation of fire and security systems.
In addition, users who are “well acquainted” with electronics can independently install and configure the Xital GSM 4 alarm - the instruction will help you perform these procedures quickly and accurately.
GENERAL INFORMATION AND BASIC PARAMETERS
Cellular control system for heating equipment KSITAL GSM-4T
is intended for notification via a cellular communication channel about the failure of the heating
equipment and remotely control it using a cell phone.
In addition to controlling heating equipment, the KSITAL GSM-4T system has
additional options for notification via SMS and voice dialing about
triggering of various sensors connected to the controller inputs. It can be
motion, vibration, glass breaking, smoke, gas leakage, flooding sensors,
pressure, or just door bell. The message text for each input can be
changed in accordance with the purpose of the sensor.
SMS can be duplicated by a voice message «
Anxiety!".
The system allows you to use «
panic buttons" to alert you to an attack or
emergency.
Messages are sent sequentially according to a pre-recorded list
phones.
Upon receipt of an SMS message with a control command, the controller can turn on
or turn off any of the three relays built into it. This allows you to remotely
control various devices such as heating, sauna, pumps,
lighting, etc. from a cell phone.
One built-in and up to five remote temperature sensors make a continuous measurement
room temperature. The system collects data from all connected temperature sensors
and sends them in a report as a table.
When the temperature in the room goes beyond the specified range, an SMS message about
are sent to cell phones, the numbers of which are previously entered in
memory.
The system has a mode of automatic maintenance of the temperature in the room, controlling
heating system using the built-in relay. Stabilization temperature value
is set by an SMS command from a remote cell phone.
Can be easily connected to the controller: external status indicator «
on the
control", for example, a street light annunciator, or a control panel
additional alarm system.
If there is a possibility of disconnection at the 220V voltage object, then it is necessary
use a 12V backup battery that will be charged by the controller as
need.
With a backup battery, the system remains fully operational for
loss time 220V, informs about the loss / appearance of voltage and discharge
backup battery.
There are two SIM-card readers installed on the controller board, the main one and the backup one.
operator. The system will automatically switch to a backup operator in case of network loss
the main operator or failures when sending SMS through it.
Having two systems configured as «
partners”, allows you to timely fix
problems with the cellular network or the use of radio signal jamming.
The possibility of sound control of the room with the help of an additional
external microphone.
The system is intended for installation inside a controlled object and is designed for
round-the-clock operation at temperatures from -250C to +500C.
The power consumed by the system from the AC mains is not more than 10W.
Number of built-in relays - 3.
Number of control zones (
inputs) - 8.
The maximum number of phone numbers for sending SMS messages is 10.
Maximum number of telephone numbers for dialing with a voice message
«
Anxiety!" - ten.
Overall dimensions of the controller - 15 x 11 x 4 cm.
Package size - 25 x 16 x 6 cm.
Weight with packaging - 1250 g.
Completeness:
- Controller" KSITAL GSM-T"
- Built-in GSM modem
- Power adapter 220V / 21V (minus in the center)
- Touch Memory electronic key reader with 10m connection cable to the controller
- Touch Memory master key used to register electronic keys
- Backup battery cord
- Remote digital temperature sensor with a 10m cable for connection to the controller (2 pcs.)
- GSM antenna
Boiler control
system "KSITAL" with a reasonable price and ease of installation, it has a wide range of features:
- Built-in GSM module
- 10 phone numbers for sending SMS
- 10 phone numbers to dial with voice message
- from 4 to 12 control zones for connecting signal loops with sensors
- 3 built-in relays 5A / 220V for equipment control
- built-in temperature sensor for measuring and transmitting room temperature
- the ability to install additional 6 Touch Memory keys, in addition to the master key
- the ability to listen to the room with an external microphone
- possibility of user programming long (up to 60 characters) SMS corresponding to triggering of control zones
- the ability to send SMS about the control and removal from control
- sending SMS in case of a critical drop in room temperature
- function of stabilizing the temperature in the room by remote setting
- uninterruptible power supply function, control of charging of the backup 12V battery, sending SMS in case of loss of 220V and critical discharge of the backup battery
- panic button function that allows sending alarm SMS when the system is uncontrolled
- automatic daily report (and also on request) on the health of the system
- setting the system for control both with the help of Touch Memory keys and with the help of SMS
- diagnostics of malfunction of alarm loops (breaks, short circuits) during control
- 12V power supply of the connected sensors directly from the controller (maintained when 220V is lost)
- temperature range from -25С to +50С (when equipped with a corresponding SIM-card)
GSM boiler control |
|
| Cellular boiler and heating equipment control system KSITAL GSM-4T GSM-8T GSM-12T |
|
|
By using gsm alarm and control - the possibility of automatic boiler control or an external heater from the built-in temperature sensor. GSM controller is intended for notification via a cellular communication channel about the failure of heating equipment and remote control of it using a cellular gsm phone. The built-in analog temperature sensor and up to 5 digital external sensors continuously measure the temperature. When the room temperature drops, the system sends SMS messages about this to cell phones, the numbers of which are previously stored in memory. In case of loss of 220V voltage in the controlled room, the corresponding SMS is also sent. The GSM boiler and heating equipment controller uses a built-in GSM module. The cellular alarm system allows you to remotely start heating equipment by SMS command from a remote cell phone. In addition to controlling the boiler and heating equipment, the KSITAL-GSM-T system has additional capabilities for notifying via SMS about the operation of various sensors connected to the controller inputs. |
|
GSM Guard (for Windows)
- designed for automated monitoring of remote objects and organizationsremote control for centralized monitoring of objects(monitoring station), equipped with GSM - control and management systems.
iKsytal program (for iOS, for Android)
THERMICS-GSM(for Android)
- designed to improve the usability of the GSM control system for heating equipment Ksital GSM-4T.
It is installed in smartphones with the Android operating system.
The program allows you to control the heating boiler, lighting, control the temperature in the heating system and the room, turn on any additional device, arm and disarm the object, receive alarm messages and much more. Allows you to set your own names for temperature sensors and output relays.
