Tire paths. Garden paths from old car tires

Many people, having bought a summer cottage, sooner or later face the need to equip the site. In particular, with the manufacture of tracks. Today, there are many ways to accomplish this task. The range of choices is great. These are various concrete and asphalt tiles, and broken bricks, and expanded clay, etc. Everything depends on the price of the issue.

You can make inexpensive, almost eternal, country paths on your own and, moreover, almost free of charge. For their manufacture, old car tires are suitable. To be more precise, only a treadmill is used from the tire itself - its tread .. For country paths, it is better to use tires from trucks. They will need much less, and the width will turn out more. Thus, you can significantly save time spent on arranging your site.

The process of "extracting" the necessary material from tires is as follows.

It is necessary to cut (separate) the tire tread from the sidewalls with a sharp knife. The cut line is shown in the figure. In order for the knife to easily cut rubber, it must be periodically dipped in oil or soapy water, and some kind of wedging device (spring or mount) must be inserted behind the knife itself. After separating the treadmill from the sidewalls, we get a rubber ring that needs to be cut, and thus get a rubber band. This tape will be our covering for country paths. When a sufficient number of such rubber bands is obtained, we proceed to the installation. To lay a country path of sufficient width, you may need from three to four such tapes.

We adjust the tapes along the length and nail them along the edges with nails to a wooden bar or board. We leave a gap of 1-2 cm between the tapes. In the future, grass will grow in this gap, which will keep our paths from lateral displacements. Tapes should be laid on moist soil. So they quickly "lie down" and bond with the ground. The wooden blocks holding the rubber bands are recessed into the ground so that there are no bumps. That's the whole process. lovers landscape design may not use the whole tape, but individual pieces. A single tape can be used to lay paths between the beds. Here already at whom what imagination. The main thing would be the desire, and the material for manufacturing can be found in almost every city dump or along the roadsides.

A. Vinogradov.

From DelaiSam.ru:

The easiest way to get old tires in tire shops. Their masters will be just happy to get rid of deposits of old tires.

In terms of garden design the use of such a coating for paths is, of course, doubtful, for example, between a flower garden and or flower beds. But to cover with such tapes a parking lot for a car, an entrance path to a site, a utility yard, a place for washing a car, inter-bed passages, etc. will be very helpful. The material is almost eternal, not slippery and looks decent.

Let me express one more application for such "ribbons" from old tires.

In spring or autumn, i.e. during the thaw period, many summer residents have difficulty getting to their summer cottages.

Now, if you line the most problematic places on the road with such tapes. And it's easy - to have a couple of such tapes in the trunk, in case you get stuck ... Usually, in such cases, fussing with a shovel begins, slipping all sorts of branches, boards, grass. Rubber on rubber, and even tread to tread, guarantees almost caterpillar patency.

And quite already enough exotic use of old tires is roofing material! Have you seen classic tiles? These are, in general, completely identical half-cylinders, some of which are laid with a chute down, and some with a chute up. As a result, water flows down the gutters from the roof.

Therefore, if you cut the tire, as shown in the figure, we get a gutter, 1-1.5 meters long! What prevents us from nailing this gutter to the crate, with the tray down, and on top of it - the same, but with the convex part up?

As a result, we get an almost eternal roof.

Well, we will not cover the house with such a roof, but here are the outbuildings, a woodshed, a shed, etc. - why not! It's just free roofing!

Recently, my aunt was introduced to her niece's blog, she, as a summer resident, was interested in the heading "Ideas for giving". Order received for good idea for garden paths. That's what I like about summer cottage construction and repair, so it's room for activity, and not only in terms of space, but also in terms of implementing the most unexpected ideas.

So, back to our sheep paths. Options - a great many, one more beautiful than the other. The tree for me will always be paramount if put before a choice. Still, a living material, breathable, warm.

Paths, consisting of different segments, connected together, also look very nice, especially when one of the segments is green in one form or another.

Mosaic of painted stones, sealed in concrete, refers, in my understanding, to artistic creativity. You create a canvas in an unusual technique.

And there is such a very simple and budget option, you put together puzzles from rubber modules, I like the fact that they can always be shifted, you never know, plans have changed, space will be required. Minute business. Although, of course, more like a temporary measure. In the end, all summer residents and owners of household plots go through a state of temporality, so it will come in handy on the farm.

On the site neumaticoadicto.blogspot.com.es, the author went further, he makes rubber tracks from old tires, but what are there tracks, toys, jewelry, furniture, shoes ... in general, when all country affairs will be in openwork (if at all really) you can equip yourself with a workshop and create there, even if only from old tires. Like this:

And from the sidewalls you can build just such a flower bed and walk around in flip flops with tire soles.

It no longer has anything to do with the paths, but completely with the dacha.

Planning the location of linear objects and determining the best option. Get advice on the topic of a linear facility layout project and order development project documentation in the company "INTERPROJECT" on the website of the company www.interproject.ru.

The presented material will be useful for many gardeners, because it contains brief information on how comfortable garden paths can be equipped from old tires.

They can be an excellent substitute for classic concrete slabs, so they are quite common in practice.

Both from a practical and economic point of view, the use of used tires for arranging special paths on land plots is a great opportunity to get rid of unnecessary material and turn its presence to your advantage.

Undeniable advantages

The main advantages of garden roads equipped with used car tires include the following factors:

Ease of care of a covering.
Rubber dries quickly, so even after heavy rainfall, walking on it through certain time comfortable and safe, as there is no risk of slipping here again.
Technical ease of manufacture.

All this indicates that the gardener is capable of preparing a path with a similar method with his own hands.

The main thing in this situation is to have a clear idea of the nature of the work to be done, as well as to observe some technological tricks.

What needs to be done

To get a quality garden path made of tires, important act according to the previously planned plan. It can be based on the following basic actions:

tires are placed on the ground in a horizontal position;
for the stability of the tire structure, they are slightly dug into the ground;
earth is poured into the holes.

Not a superfluous practical step would be the use of gravel as required material for powder, because it does not allow shoes to slide on rubber when it is still wet. Thus, the gardener will save himself from hypothetical injuries associated with the consequences of possible falls.

Of course, the very appearance of the untreated surface of car tires can hardly become an ornament on the territory. land plot. And in order to give such paved paths a nice design, the use of paint is quite acceptable.

For example, a track painted in black and white looks great. It seems to form a stylized composition of a chessboard. In any case, outwardly it all looks very unusual and creative.

Therefore, many visitors and guests are able to appreciate a similar creative idea of the owner of the garden plot, who arranged such transitions on his own land plots.

In any case, the scope for creativity here is simply colossal, which must be beaten with the help of your ingenuity and practical skills.

And one day the garden can turn into a wonderful place to spend as much of your free time here as possible, enjoying nature and original design its land area.

Often, the owners of garden and summer cottages are faced with the fact that it is almost impossible to walk through the garden after rain. Mud sticks to shoes, and if you slip, you can even injure yourself. Wealthy people hire a designer to solve this issue, who develops a design project with the inclusion of garden paths. But in order to save money, you can not only make a drawing yourself, but also lay out garden paths with your own hands. And what is needed for this will be discussed in this article.

Peculiarities

Garden paths can be a permanent or temporary structure. As for temporary tracks, they can be dismantled and moved at any time, but capital ones are made once and for all, therefore before starting installation, it is important to lay them in advance on the drawing.

Laying paths in the country should be made taking into account shrubs, trees, beds and greenhouses.

Keep in mind, after a few years, the plants can grow to such a size that they begin to interfere with movement around the site, and in some plants, the roots can completely damage the trails. To avoid this, experts do not recommend laying building materials near plantings. It must be remembered that the construction of new outbuildings in the future should not have any obstacles. Otherwise, you will have to dismantle and lay new tracks, and this is an additional waste of both time and money.

When choosing a material, it is necessary to build on the fact that it must be reliable, with a long service life, safe not only for movement, but also for the soil. You should weigh the pros and cons before buying building materials that can rot, corrode, be colonized by mold fungi and other harmful microorganisms. The climate must also be taken into account, especially the temperature in winter time year and snow cover, so that the material has frost resistance and winter hardiness.

In the case of repair work, no difficulties should arise, otherwise the entire alley will have to be dismantled. From this point of view, the care of the track should not cause complications.

The choice of building material is determined by the frequency of use and functional load. For example, for those trails that are rarely traveled, bulk materials are suitable - gravel, crushed stone or sand, including the use of cork bark. In places where there is a large flow of people, durable materials such as concrete, rubber, brick or monolith are suitable. This can also be attributed to the paths along which it is planned to move vehicles or loaded wheelbarrows.

Making tracks with your own hands is a creative process. It depends not only on the financial situation of the owner of the site, but also on his skills. But often this issue can be solved with minimal physical and material investments.

What will be needed?

Depending on the material chosen, you may need geogrids, a concrete mixer, a wood saw, a metal saw, a hammer, a mallet, and even ordinary scissors. In addition, do not forget about the building rule and the building level, thanks to these tools you can level the surface and make it perfect.

You can’t do this work without shovels - shovels and bayonet, without a rake, in less fertile areas you may need pitchforks and scrap. With their help, markup is carried out, unnecessary land is removed, which is put in a wheelbarrow. An alternative to a wheelbarrow are metal buckets.

The project plan is carried out in specialized computer programs or on a regular sheet of paper with a pencil or pen. First you need to draw a house, a barn, a bathhouse, a toilet, then a gate and a central gate. Paths are schematically drawn directly to these objects. Additional paths are marked to the gazebo, pool, barbecue area. Do not forget about the approaches to the beds, water system, greenhouses. As for the width of future tracks, their marking will have to be carried out on the ground. This can be done with pegs, a hammer and twine.

After the pegs are driven in, they are connected to each other with twine. The width of the alley should ideally be suitable for the movement of not only people, but also construction wheelbarrows. Instead of pegs, marking can be done with sand, it is sprinkled in a small amount, but at the same time it should be visible from the side. Thanks to this, you can plan flower beds, beds and other plantings in advance.

Simple budget options

In recent years, geotextiles have been very popular among summer residents. The black canvas is used for weed control. As you know, plants need sunlight, without it nothing living can grow, and weeds are physically unable to break through geotextiles due to the fact that the material prevents the penetration of ultraviolet radiation. Some craftsmen use it as an option for garden paths.

On sale, covering material is found in white and black, the second option is suitable for construction work. Its density is 60 microns - which means that it will last for several seasons. The width of geotextiles usually has an indicator of 3.6 m, and any length can be cut.

To make a track from this material, it must first be cut. If you fold the material in half, you will get segments of 80 cm - this is quite enough for small paths.

It is important to note that the soil remains in place, while in other options a few centimeters of earth will need to be removed. Thanks to this, the installation process will take less time.

Usually paths are made in those places where paths have already been laid and the earth is dense there, so you will have to tinker with it. For this work it is necessary to use a bayonet shovel with a rounded base. With its help, a small gap is made, and then geotextiles are pushed into it. This stage continues first on the left side, and then on the right.

As a result, the edges of the material should be completely in the ground. In practice, it is enough to “bury” 10 cm on one side and 10 cm on the other side. Keep in mind that it is desirable to stretch the material, otherwise “pockets” may form, and if there are small children in the family, they may stumble and hurt themselves.

The ground around the path must be tamped. It is enough to walk along it several times back and forth. Under the influence of precipitation and ultraviolet radiation, the earth will seize and hold the material as tightly as possible.

Installation of the next segment is desirable to overlap. Joints between building materials can be sealed with metal staples or pieces of steel wire. For this, two materials are “sewn together” with staples, clogging is done with a hammer. This operation is also performed to secure the ends of the geotextile.

From tires

From old tires, you can create a high-quality wear-resistant coating that is not afraid of rain, snow, or the scorching sun. In addition, rubber perfectly tolerates temperature changes and lasts for several decades.

Maintaining this path is easy. It is enough from time to time to sweep away the debris with a broom, and after the dirt has dried, rinse with a strong pressure of water from a hose. After wet cleaning and after rain, the water on the rubber surface dries quickly, so accidental falls can be avoided.

After the building material is assembled, the paths will be created, but before you start laying, you need to make a rubber hoop. For this, a car tire is taken and laid on the surface. It is best to use an old two hundred liter barrel.

First, rubber is cut near the side, this procedure is easiest to perform with a shoe knife. After the appearance of a small incision, a well-sharpened large knife is taken. By moving the knife up and towards itself, the tire is ripped open. For convenience, the cut off must be slightly bent to the side. Having dealt with one side, you have to do the same with the second.

Keep in mind that the knife must be sharp enough to do the job without nicks or wedges. Periodically, the knife must be moistened with grease and wiped with a cloth so that it is a little slippery.

The rubber hoop has to be turned inside out, for this the cut tire is laid on the ground and, fixing it with your feet, this procedure is carried out with your hands. It remains only to break the inverted tire on the sides to the state of the hoop. Do not forget about safety precautions - it is advisable to use gloves.

In order to make a rubber band, the workpiece is transferred to a bench or stool. And fix its sides with a clamp.

It is important that the rubber is in a state of tension, since there is a metal case inside the tire. If you start cutting metal with a knife, then the knife will quickly become dull, so trimming is done using an angle grinder.

Experts recommend to follow the direction of the wind, ideally, it would be for it to blow not towards the neighbors, but onto the roadway. Otherwise, the neighbors may not like the smell of burning rubber. Try to avoid getting sparks on the skin and especially in the eyes. At the end, it remains only to remove the clamp, and the rubber band is ready. Such tapes need to be made as much as it takes to create garden paths.

The cut tape is to be fixed on a wooden block - a hammer and nails are suitable for this. What width the path needs, this length should be the board. Usually they fill two or three rows, it will not work without joints at all, which means that weed control will be in the future.

Before installation, the ground must be leveled and well tamped. The resulting products are placed in the moistened earth. The protruding part of the timber must be completely trampled into the ground to get a flat garden path.

Some people remove the ground before laying and fix the rubber in such a way that waves eventually form. Either sand, or gravel, or pebbles are poured into the resulting pits.

On uneven areas where there is a steep slope, a ladder is made of tires. Protrusions are made from bottom to top with a shovel, into which automobile wheels are laid. The first row should correspond to the dimensions of the tire, and the second and subsequent ones should be a little narrower.

So that the tires do not budge, the extracted earth, gravel or sand is filled up, after which ramming takes place, gravel is sprinkled on top.

Additionally, the structure can be fenced with boards or stakes to prevent slipping. Manufacturing plants, recycling old tires, produce special rubberized tiles of various colors that are suitable for creating garden paths. Fastening is carried out thanks to the castle connection.

Professionals advise laying thin slabs on cement screed, the surface of which is previously leveled.

From plastic bottles

You can lay out the track from another recyclable material - plastic bottles. Moreover, you can accumulate the material yourself or agree with friends, acquaintances and colleagues. Of course, this will require several hundred plastic bottles of various capacities, but at the same time, such an arrangement will not hit the family budget.

The advantages of this finishing material include multi-colored coloring, durability, strength and ease of installation. Of the minuses, melting at high temperatures, the likelihood of slipping after rain and the fact that the material fades under the influence of sunlight can be noted.

Keep in mind that in addition to the container itself, bottoms and lids can also be used in the work.

Plastic bottles must be thoroughly washed from liquid residues before laying. At the time of washing, it is advisable to tear off all labels and remove adhesive composition so that particles of dirt and dust do not stick to it. After that, the plastic is either wiped dry or dried on a sunny day in the fresh air.

Prepared finishing material stuffed with earth, if sand remains after construction, it can also be used. There should not be any voids inside the container; it is necessary to carefully compact the earth or sand. This is done so that at the time of walking the bottles are not squeezed by the human weight.

Children can be involved in this work, firstly, it will distract them from other activities, and secondly, it will allow them to cope with the task in less time.

Then you need to remove the soil. For this, a shovel and a wheelbarrow are taken, the earth is removed by about 25-30 cm. The fertile layer can be used in beds or in a greenhouse. The formwork is made of boards, the thickness of which should be about 16 cm.

The boards are screwed to the pegs with a screwdriver and self-tapping screws. If a special tool is not at hand, then a hammer and nails can serve as an alternative.

To avoid shrinkage of the soil, it is advisable to walk on the ground several times back and forth, and then fill the path with construction and household waste. It can be branches, broken bricks or flying leaves. In order to prevent debris from flying around the site, it is covered with sand. I would like to point out that it is the sand that will not allow the future track to sag.

The first row of plastic bottles is laid on the sand cushion. Laying must be done along the direction. Boards are temporarily mounted on top of the eggplants, after which you need to jump on them well. Thanks to this, the bottles will be evenly distributed over the surface, and the resulting voids will have to be filled with a cement-sand mixture. Subsequently, the mixture is abundantly wetted with water, and when the cement dries, the first row will be ready. Usually one row is enough, but if there is room for another one, then the process should be repeated, but without laying household waste.

The use of small containers has been described above. If five-liter bottles are available, then after washing and drying, they need to cut off the bottom. Such bottles need several tens or hundreds. When they are ready, you have to insert one bottle into another and lay the resulting forms in a trench. It remains to cement the track in the manner described earlier.

A whole mosaic panel can be laid out using plastic covers, but, unfortunately, a lot of building materials are needed. In order to lay a linear meter of a garden path, you will need hundreds of covers. But at the same time, you can create a beautiful drawing that will delight not only household members, but also guests.

First of all, corks are laid in the direction of the path, boards are temporarily mounted on top, on which you have to walk. Thanks to the chaotic movements, the corks will be compacted and will be on the same level.

To get rid of the gaps, the seams are covered with sand, the boards are laid on top again and the final compaction takes place. It remains only to clean the surface of excess earth and sand, a brush or a broom is suitable for this.

The bottoms of plastic bottles are laid in a similar way. Keep in mind that such a track is not suitable for permanent use, because it does not have wear resistance. Country craftsmen, based on their experience, recommend using bottles made of durable plastic.

To date, the production of plastic tiles has also been established. Due to its qualities and light weight, it is very popular among summer residents.

from wood

Do not lose their popularity and wooden paths. They are made either from boards or from saw cuts. Wood is not only a natural material, but also a durable, stylish product. Wood is easy to process, so the installation of tracks can be done by hand.

Many on summer cottages there are old cut fruit trees- pears, apples, cherries. But it is best to use oak, birch, beech, pine or larch stumps for this procedure.

It is advisable to acquire building materials of various diameters, thanks to which winding paths can be laid.

It's no secret that a tree that has not been treated for fungal diseases and moisture quickly becomes unusable. Therefore, in no case should you lay freshly sawn round timber. Drying oil is suitable for processing, which is brought to a boil. It is important to coat the saw cut completely, and it is better to completely immerse the stump in a vat of drying oil so that the material is absorbed. It is advisable to perform this operation by professionals, since you can get burned.

For safety reasons, you can use special antiseptic solutions sold in hardware stores. The round timber is completely placed in the solution for several hours. It is allowed to apply the solution with a brush or roller. Additionally, experts recommend treating the bottom of the plate with bitumen, and the surface with copper sulphate. Further actions with wood are performed only after complete drying.

There are soft woods - pine can be attributed to them, and hard ones - oak, beech, larch. By the way, processed larch will easily lie in the ground for 25-30 years, but pine will last only 5-6 years, after which the path will have to be dismantled.

Only dried wood, not inhabited by pests and without cracks, is suitable for work. The ideal height for dies is 15-17 cm. The height is measured either with a ruler or a tape measure. With the help of an ax or a cleaver, the bark is removed.

It is important that the cut was made with an electric saw or chainsaw perpendicularly.

The optimal width of the garden path is 70-75 cm. The winding path looks great on the garden plot. To create it, you have to remove the top layer of the earth. Sod is easiest to remove with two people - while one person works with a shovel, the second rolls the lawn into rolls. Rolls can later be moved and laid in another place.

Geotextiles are laid out in the resulting trench. As noted earlier, weeds do not break through it. A layer of sand or gravel is poured onto the geotextile - this is drainage, and round timber is laid. You need to start laying with large circles, then medium ones are laid out, and only then - small ones. Try to select them in size so that visible voids do not form. Do not forget to check the evenness of the surface with a building level. If there are differences in some place, then you need to use a hammer. Hemp should be laid above the lawn by about 3 cm.

If a border is planned, then its installation must be completed before laying the saw cuts. For this, brick, stone or chubuk are suitable.

Unfortunately, it is impossible to do without voids. To repair them, you will need to split or saw the round timber and lay its parts between the cuts. Sand or gravel is poured over the base. It spills abundantly with water. The building material will settle under the pressure of water, so additional backfilling will be required.

The final step is decoration. You can paint the round timber or lay pebbles in the voids, or leave everything as it is - this choice remains with the owner of the site.

Remember that the track needs annual maintenance. Periodically, it will be necessary to clean the surface, treat it with antifungal agents and fungicides. As the protective layer dries, apply a new layer of drying oil or acrylic paint.

Several round timbers should be left for the future, so that in case of repair, failed stumps must be dismantled and spare ones put in their place.

Another type of wooden garden path is a board path. Installation is faster than laying round logs, and special alignment is not required in this case.

Coniferous trees are considered a cheap option for laying. In this case, the thickness of the board should not be less than 5-6 cm. Usually raw materials are sold in building stores. edged board. In this regard, it will be treated with antifungal agents, and then with varnish or drying oil.

Using a hacksaw, identical lamellas are cut. If you have a special tool at hand, then this work will be done faster. If a rounded path is planned, then the boards may differ from each other in size.

Keep in mind that boards from pallets can also be used. Some people even stack whole pallets. But today, the production of terrace boards has been established, it contains wood chips and polypropylene. Such building material does not require processing, while it is easily cut to the desired size.

The process of preparing the foundation has already been described earlier, so it makes no sense to repeat. After that, you need to mount the frame. A beam is suitable for the frame, which is laid every 50-60 cm. The beam is connected either with metal elements or boards. The main cover is screwed to the frame perpendicular to the direction. To perform connecting work, use a screwdriver and self-tapping screws of the required length. If elevations or depressions appear along the path of the path, the construction of steps will be required.

Concrete

Concreting is another budget option, but at the same time, concrete paths are capital structures that will last 20-26 years. Therefore, it is very important to approach this issue with all responsibility, since in the future it will not be possible to change the direction of the tracks in a few minutes.

They are made of cement and sand, in connection with this, it is necessary to purchase a sand machine and several bags of cement in advance. The exact amount will depend on the width and length of the future structure.

When digging a trench, it is important to pay attention to the soil. If there is a lot of sand in the ground, then concrete can be poured directly into the trench. But for most regions, water disposal will be required. To do this, a layer of rubble is laid at the bottom of the pit. Enough 9-13 cm, and for strength, you can pour 15 cm.

Remember that before filling the rubble, the earth must be tamped.

If a central drainage system passes along the path, the pipes must be “sheathed”. The path should rise about 2-3 cm above ground level. Formwork will be required for rounding. Plastic or a sheet of plywood will do the job just fine.

To save on formwork, experts recommend making it in parts and rearranging it after the first pour has dried. Formwork can also be made from boards. Its width should correspond to the width of the future alley. It usually ranges from 60 cm to 90 cm.

The next step is the installation of a waterproofing layer, for this, roofing material or agrofibre is used. If covering material remains on the site - geotextiles, it can also come up. A layer of gravel or crushed stone is laid on top of the waterproofing, followed by a layer of sand. The resulting pillow should be thoroughly spilled with water.

Unfortunately, concrete takes a long time to dry, usually taking a month. During this time, there is a high probability of cracks appearing on the surface. To avoid this, before the screed dries, every 3 m, wooden slats. They do not allow concrete to expand.

To stiffen the structure, some summer residents use reinforcement. For this, wire, self-tapping screws, nuts, screws, nails, pipe trimmings or a chain-link mesh left over from an old fence are suitable. If a construction debris not at hand, then in the store you have to buy a special reinforced mesh. A solution is poured onto the fixed grid, and it will take less than if you make a track without it.

Dacha is a place where you want to relax after the bustle of the city. Therefore, it must have everything necessary for comfort, including paths on the site, on which not only ease of movement, but also safety depends.

Today, for the manufacture of paths in the garden, you can use various materials. Someone prefers paving slabs, or gravel, but someone goes a more radical way, and makes tracks from old tires.

Indeed, car tires are very suitable material for these purposes. In addition to decent physical and mechanical properties, the tires have a tread that will make driving on homemade tracks as convenient and safe as possible.

How to make tracks from old tires? What tires are best for this purpose? Read about it in a construction magazine.

Original and beautiful tracks from old car tires are not just a budget option. This approach to the arrangement of the garden plot will embellish it and distinguish it from many.

It is also noteworthy that for the manufacture of such garden paths with your own hands, you will need a minimum of time and tools. By the way, you will need a grinder from the tool, but a jigsaw with a metal file is better. If a electric jigsaw No, you can also use a sharp knife. However, the work on the manufacture of tracks, in this case, will be seriously delayed.

First of all, you will need to cut the sidewalls on the tires so that you get rings. As mentioned above, for work it is best to use an electric jigsaw with a metal blade. After the sidewalls are cut out, it will be necessary to cut the tires in half so that separate strips are obtained.

To align the strips, it will be necessary to make small cuts on them from each edge, up to 5 cm. Thus, when laying garden paths from tires, there will be no difficulty in leveling them.

For the manufacture of tracks, you can use various tires, ranging from R13 and larger. Some masters, at all, take D20 tires from DT. However, in this case, there may be some difficulty in cutting the side of the tires. And the high tread height can become an obstacle to comfortable movement on homemade tracks.

Therefore, it is recommended to take tires that are not too large, and exclusively from cars. It will also be just fine if there is at least some tread left on the tires. Then the garden paths will not be as slippery as those for the manufacture of which a mine belt for conveyors (conveyor) was taken.

In order for tire tracks to last for a long time, you should follow the basic rules associated with their installation. For these purposes, you will first have to mark the territory and prepare the site for the tracks.

Therefore, armed with a length of rope or fishing line, as well as several wooden pegs, you should mark the boundaries where the tracks from the tires will pass with your own hands. Then you can prepare the base for their laying.

If there is vegetation in the place where garden paths are laid, then in any case it is necessary to get rid of it. Then, using a shovel, you should carefully level the soil under the paths (the place should be flat, without depressions and protrusions).

The last step will be the laying of tracks from car tires. There is nothing complicated about this, the main thing is that the home-made paths fit well to the surface of the ground and do not fidget on it.