→ How to drain water from a stretch ceiling?

27.

What to do with them?

There are defects in the production, storage and manufacture of the canvas.

Typically, such defects are visible immediately after the installation of the stretch ceiling canvas. Therefore, it is recommended to carefully accept the work done - carefully inspect the finished ceiling.

The most common storage defect is creases on a glossy stretch ceiling.

Creases on glossy stretch ceiling

These are traces of the collapsed state of the stretch ceiling. Usually they disappear on their own within a week to a month - verified. To avoid the stretch ceiling is made as close as possible to the date of installation.

Defects on the glossy stretch ceiling

Manufacturing Defects:

Defect on a satin white stretch ceiling (stripes, folds)

Solution: changing the canvas. Of course have been tried different variants exposure - heating with a hairdryer, washing with soap and powder, rubbing with a damp cloth. Zero effect. This disadvantage arose during the production of the material at the manufacturer.

Another irreparable defect is abrasions:

Stretch ceiling defect - abrasions

It can be hard to see in the photo, but there are such matte spots - they are visible on the reflection of light objects. In my practice, they met only on lacquered colored ceilings and on a glossy "sky". The defect occurs when transporting such a fabric without a gasket (light translucent fabric). In the process of shaking, rubbing occurs at the fold points.

Solution: changing the canvas. You can also do it differently. Such scuffs are visible only in the light. If it is possible to unfold the canvas when installed in a damaged place in an unlit corner of the room (where it is not possible to see the reflection of the window in the ceiling), then see this shortcoming it will just be impossible. If there are defects on the entire surface of the stretch ceiling, then it will have to be replaced.

In general, an experienced worker in the workshop can notice defects and immediately replace the canvas, without bringing it to installation with subsequent replacement.

And here is another defect that occurs when the profile and material of the stretch ceiling overheat. With a large shrinkage of the material (the stretch ceiling is much smaller than the size of the room - this also happens), the tucked part of the canvas pulls the profile. And since you have to heat it up a lot, the profile deforms a little, and such an unevenness arises. As you can see, even a stub cannot hide such a defect.

Stretch ceilings differ in a number of advantages from other options for finishing the room, which makes many customers stop their attention on this particular option. Currently, they are the best solution that will perfectly complement the room, made in any style. In the range of companies that sell and install materials, a large selection of products is presented, which allows you to create the perfect interior that exactly meets the wishes of customers. Given the demand for products, products of different quality are presented on the market, as a result of which some ceilings lose their attractive appearance after some time after installation. What is the reason for this: poor quality of the canvas, improper installation, or, perhaps, inappropriate surface care? This material will help to understand this, because further we will talk about the actual problems that some owners face after installing a decorative canvas.

Frequently Asked Questions

Each client wants to get excellent quality and performance characteristics product. But our expectations do not always correspond to reality. And here we are talking not only about poor-quality material or other errors from manufacturers and specialists who installed the ceiling. Defects, which will be discussed below, can be encountered by absolutely every buyer.

Many customers want to hear the answers to these questions:

1. Why do pimples and other marks appear on the stretch ceiling? This may be an installation error. During installation, the pimply substrate could stick to the canvas. This is easy to check. When you touch the problem area with your fingers, you can feel a characteristic seal.
2. Why do stripes appear on the stretch ceiling? This is also a mistake of the masters when performing the installation. The appearance of stripes on the canvas indicates overheating or underheating. The installation technology may also be violated, because the matte canvas and satin need to be filled in a circle. Only by creating tension, you can get rid of the waves, which subsequently turn into characteristic stripes.
3. Why does the stretch ceiling sag under the chandelier? This can happen in large areas. In such rooms, experts advise buying not one whole canvas, but choosing several parts of the finishing material.

By choosing a responsible company that is engaged in the production and installation of decorative paintings, the owners of the premises can avoid such problems.

An equally pressing issue

Are you wondering why the stretch ceiling is cracking? You can determine the cause of the appearance of characteristic sounds depending on their frequency. If crackling occurs rarely, then this is an indicator improper care behind the surface. If sounds are heard regularly, most likely a mistake was made during the editing process. But the exact conclusion can only be given by a specialist after examining the object.

In fact, the reasons for the appearance similar sounds may be mass. That's why the stretch ceiling clicks:

• there are violations during the installation of the profile;
• poor-quality installation of the canvas;
• temperature fluctuations are observed. This is often observed in the hallway, when in winter time the door to the street opens;
• there is a change in humidity in the room, this is typical for the kitchen or bathroom;
• it is possible for air to enter the opening between the concrete floor and the canvas, which is quite likely when cracks form;
• there were cockroaches and rodents.

In addition, the cause of cod may be not only in the fasteners or in the canvas itself. Sometimes such sounds are made by walls to which profiles are attached. This often happens in old houses.

Everyone understands that a properly installed structure should not make any sounds, therefore, in order to get rid of the problem, it will take a lot of effort. If this happens due to a violation of the installation technology, you must contact the company that performed the work, or another organization that specializes in this issue. But in the second case, it should be understood that the work will need to be paid in full. Please note that it is unlikely that a non-professional will cope with such a problem, so it is better not to experiment.

If the reason for the appearance of such sounds is a sharp change in the temperature in the room or the level of humidity, the owners should familiarize themselves with the features of the care and operation of such ceilings.

Another problem is sagging or sticking to the ceiling of the canvas

This often happens both in apartments and in private houses, while the reason for this phenomenon in most cases is the same. Why does the stretch ceiling stick to the ceiling or swell? Many homeowners who encounter this problem believe that the fault lies with the installation company. This is a wrong opinion.

Absolutely every canvas can be subject to such deformations. At the same time, this happens not only with PVC film, but also with the fabric version, which is usually more tightly stretched and can pass air masses through itself.

Why is the stretch ceiling sagging? It is a soft canvas that can change its appearance when it is influenced by various phenomena, for example, pressing with a hand, a breath of wind or water flowing.

When the problem is precisely the wind, the stretch ceiling shows where the air masses are directed in a particular room. Here the question immediately arises, where do they come from in the room. When opening the doors, a stream of air enters the balcony or landing in the room. That is why the stretch ceiling either sags or stretches.

This problem may occur indoors. How? This often happens in houses where the construction of the house is of poor quality, including where there is poor sealing of floors between floors. Wind enters the gaps between the boards and panels.

A similar problem can be solved by sealing the gaps, but this is usually done before the ceiling is installed. If the canvas is already located, you can use special ventilation grilles. Wind flow is one of the main reasons why a stretch ceiling swells.

The Mos Sealing experts have installed a flawless ceiling for you, even, smooth with a uniform white/beige/blue or any other color that you like so much. And suddenly everything is spoiled: a spot appeared on the stretch ceiling!

Don't worry - it's not scary at all! Returning the former beautiful view of the ceiling is not a problem, but an ordinary task. To solve it, you first need to know the cause. Depending on what the ceiling canvas is stained with, different tools and means are used.

Consider what most often appear and how to remove stains on a stretch ceiling:

Water. In bathrooms, dust never settles on the ceiling (tension materials are antistatic), they also do not condense (the film is so thin that there is no temperature difference), however, splashes from the shower during bathing can hit the ceiling even for very neat people.

Given the complex chemical composition water flowing from our faucets (instead of the welcome H2O), when the drops dry, there are whitish spots on the ceiling. There are two ways to remove them - wipe with a dry cloth immediately after bathing; wipe with a damp cloth or a slightly damp, lint-free cloth.

Similarly, it is easy to remove any other water-based liquids. For example, a cherry compote exploded, during preservation, the juice of tomatoes or apples splashed onto the ceiling, a mosquito was swatted, and traces of blood remained on the ceiling.

In all these and many other similar situations, you can remove a stain on a stretch ceiling with a regular damp cloth.

Fat. Grease splatter and soot deposits are usually a problem on kitchen ceilings. To remove these stains, fat-dissolving soap compositions are needed (which ones, we will consider later, and now we will analyze the technology).

To wash hardened dirt and grease, you need to take warm water (from 40 ° C) and completely dissolve the soap in it, whipping until a thick foam forms. With a soft tool dipped in warm foam, in non-circular movements in the direction from the seam (if any), you can wash the film.

But before washing the ceiling, make sure that you do not have sharp rings or bracelets on your hands that can damage the ceiling canvas. Do the cleaning from a stepladder or stool, but not from the floor with a mop (it is so difficult to calculate the pressure and you can scratch the film on a concrete floor slab). After you make sure the ceiling is clean, wipe it dry.

Construction dust. When drilling walls during repairs, a lot of dust is generated, especially from brick and concrete walls. She settles everywhere, including on the ceiling. Ideally, if you have, you need to use a vacuum cleaner for subsequent repairs.

This is exactly what Mos Siling installers do if the walls are already finished so as not to spoil their coating. If the dust still settled on the ceiling, it is best to remove it with a vacuum cleaner using a nozzle with a long nap (do not rub with a cloth or washcloth - there may be large scratching particles in the dust).

Dye. If the pipes entering the ceiling are metal, they need to be painted from time to time. At the same time, splashes from the brush can leave spots on the stretch ceiling. In this case, efficiency is important.

If you immediately notice such a nuisance, use a tissue napkin (prepare it in advance, and then you don’t have to look for something in a hurry) - and the stain will immediately disappear. The problem will arise if you let the oil or enamel paint harden (water emulsions are washed off after hardening).

In no case do not use solvents (acetone, turpentine, white spirit, etc.), and even more so do not try to pick off the stain with sharp objects - in addition, you will get scratches or a hole. If the stain does not wash off with soapy water, it is best to decorate it with a sticker to match the color and style of the room.

How to wash a stain on a stretch ceiling

Now consider the tools that will help you get rid of blots on the ceiling. You can use napkins from:

• bamboo;
• microfiber;
• non-woven materials: thermobond and spunbond, chemicalbond and spunlace, as well as airlaid made from cellulose and synthetic fibers (polyester, viscose, polyester or polypropylene);
• lint-free fabric, such as flannel;

as well as sponges for washing cars or dishes. But you can not use piercing and cutting tools, including metal and plastic brushes and washcloths.

In order to wash the stain on the stretch ceiling, you can use any soapy substance:

• household liquid soap and remnants;
• "Myth" and "Fairy", "Frosch" and "Eared Nanny", "Pemolux" and "Pril", "AOS" and "Sorti", "Biolan" and "Dosia", "Morning Fresh" and "Lazurit" - in general, any non-abrasive gel or dishwashing liquid;
• in the same way, any washing powders are suitable, but dissolved so that no solid particles remain.

There are also special products for cleaning stretch fabrics, they are available in the form of sprays, gels and liquids. These compounds, of course, are more expensive. In addition to surfactants, they include alcohols, for example, isoropylene (harmless to tension materials and dissolves fat well).

Do not use abrasive cleaning pastes, powders, bleaches or other aggressive products such as acids.

Stains on stretch glossy ceiling

When you want to clean a varnished canvas, everything said about abrasives applies to them in particular. You should know this nuance: frequent washing glossy film will turn it matte over the years.

But there are also economical ways to clean stains from the lacquer canvas and restore shine. These are compositions for washing mirrors and glasses based on ammonia or homemade 10% ammonia solution. Even if you washed with soapy water, wipe it with ammonia at the end - and the film will shine like new.

Conclusion - about cleaning the fabric

Stains on a stretch fabric ceiling can be removed in all of the above ways, depending on the nature of the dirt. But the fabric has two features:

1. She doesn't like water, so you don't need to pour it in, just a wet wipe will suffice.
2. If the stains are not washed off (due to the high porosity, it is more difficult to wash the fabric than films), the ceiling can be painted with a water-based emulsion. This process can be repeated up to 10 times.

When a stretch ceiling is cut, you definitely should not panic. After all, there is effective ways repair of this product available to anyone. You will find them at the link. This resource is used by a huge number of users. For example, a family from the city of Odintsovo, who had a severe cut in the stretch ceiling canvas, easily coped with the repair of the product, guided by useful information.
It all happened during the installation of a home projector. The owner accidentally damaged the film of the product with a screwdriver. The cut was quite noticeable, which significantly spoiled the aesthetics of the interior in the apartment. We already talked about replacing the coating, how the problem was solved in an ingenious way: a special hole was made at the site of the cut and a lamp was mounted there.
There are other ways to get rid of a cut with your own hands. You just need to be patient and find the most suitable option getting rid of damage to the stretch ceiling with sharp objects. To thoroughly understand the topic, you need to know the causes and nature of the damage described.

Causes of material damage

The fabric of tension products has a lot of advantages:

• fast installation;
• minimum waste during installation;
• does not lose color;
• resistance to high pressure(withstands 100 kg per sq. m.);
• perfectly holds the plane and so on.

However, despite all these positive qualities, the product is very easy to cut. It is in the nature of the material that the cause of the damage lies. stretch ceilings. Experienced craftsmen try to use sharp objects as little as possible when installing the canvas. This significantly reduces the risk of damage to the product.
In many cases, the material of the stretch ceiling is torn during the skidding of large-sized furniture. Especially when the apartment is small and does not provide enough space to move around. Such troubles accompany the owners during cosmetic repairs.
When installing lighting fixtures, you also need to be careful. When cutting wires, you can inadvertently hook the surface with installation tools. It is recommended that after using screwdrivers, pliers, pliers or wire cutters, immediately put them aside. This approach will protect the described product from premature damage.

Stretch ceiling repair after damage

The cost, time and complexity of repairing the product depends on the nature and location of the damage. If the cut is minor, then you can easily stick a piece of duct tape of the same color. A good analogue is the original decoration. You can also do the same for the family from Odintsovo: install an elegant lamp.
All of these options are acceptable and fairly easy to implement. The situation is more complicated in cases of large cuts. If the canvas is severely damaged far from the edge of the product, then the product must be replaced. The same applies to fabric materials of stretch ceilings, wherever there is a cut.
It is relatively easy to repair a stretch ceiling if the damage is close to the edge of the wall. In this case, it is necessary to stretch the canvas and mount in the profile that part of it on which the cut is located. A more detailed algorithm of actions is presented below:

• using a spatula, remove the edge of the stretch ceiling in the cut area, after opening the baguette;
• with a special device, heat the part of the wall where the cutting will be done, as a result, the harpoon (the part of the canvas inserted into the profile) will become more elastic;
• carefully remove the canvas from the profile;
• make a sample of the harpoon along a special edge and carefully clean it from the remnants of the material;
• cut off the sponge located on the harpoon in the area of ​​damage (this will prevent the formation of wrinkles on the material, as well as ensure more efficient bonding of the harpoon to the web of the tension product);
• carefully glue the harpoon and the material with superglue overlapping in the same way as it was done by welding at the manufacturer's factory;
• the excess web is cut off, leaving 5-7 mm to achieve maximum rigidity of the bonding of the material;
• wait until the glue is completely dry and heat the canvas again;
• mount the elastic material again with a spatula into the profile.

Please note that the presented method is relevant only with a PVC sheet. In the case of a fabric product of this purpose, it will not be possible to stretch the surface. Another very important nuance is the warranty. If the stretch ceiling is torn due to the negligence of the installer, it makes no sense to repair the damage at your own expense. You have every right to use its repair service free of charge. Use the services and advice of qualified professionals only. This increases the likelihood of a positive outcome.

As soon as you installed the stretch ceiling, there was a reason for admiration! But suddenly it turned out that for some reason: whether it was careless handling of water by neighbors, or adverse weather conditions, an unpleasant bulge formed in your wonderful ceiling, or in other words, the ceiling swelled.

Having discovered this trouble, you ask yourself: “But how could water seep through concrete slabs”? (If we consider the option with standard apartments, standard houses).

Let's try to figure it out. The fact is that there are joints between concrete slabs. Despite the seemingly tenacious welding fastening of the fittings between these plates, the gap still remains, in which the insulation is placed. This is where the "trick" can be expected. Well, if the concrete base has cracked, then the possibility of water penetration is already obvious.

Not superfluous, but a necessary solution before installing a stretch ceiling is - testing the ceiling base, with the help of professionals. If you have already done this, or have not done it, but the ceiling still “flowed”, unfortunately, no one is safe from this, then of course it is necessary to take up the solution to this problem.

The main step to solving this problem is slowness. Do not take the initiative once again, trying to get rid of the water yourself. Leave this type of work to the professionals!

With the arrival of specialists, the problem will be eliminated, they:

• dismantle the desired angle of the stretch ceiling;
• using a special hose, drain the water;
• dry the canvas, returning it to its original form.

After all the necessary procedures, the ceiling will “shine”, as before, as if nothing had happened. Your ceiling will "heal" new life without compromising the visual appeal of your interior or your wonderful mood!