Kitchen repair service center. Do-it-yourself kitchen furniture repair

If something in the old furniture is broken or lost appearance However, this does not mean that it needs to be changed. Furniture can be restored, and any furniture, including kitchen furniture. To begin with, it is important to determine what exactly is broken, whether it is possible to fix it, whether the repair will be temporary or the furniture can still last for a long time. In the event that the set is made of solid material or only the correction of cosmetic defects is required, do-it-yourself kitchen furniture repair justifies itself. This is especially true of wooden furniture, it can be repaired repeatedly. But more affordable furniture made of MDF and chipboard can also be repaired when, for example, you need to improve the appearance of facades.

Cosmetic repair of kitchen furniture

Usually the kitchen loses its appearance the fastest, and this is most noticeable on the facades. If these are MDF facades, then in some places the film lags behind (vulnerabilities are the ends of the facades), scratches appear, spots from various contaminants appear, such as grease, the coating changes color and becomes uneven in tone.

Restoration of minor damage

Minor damages include chips, scratches, abrasions.

Chips are removed with wax. The chip, pre-aligned along the edges, is poured with molten wax, polished, and then painted over with special felt-tip pens, choosing colors. Then fix with a finishing layer of varnish.
Scuffs are rubbed with a soft microfiber cloth, on which a dye from a felt-tip pen is applied.
Scratches are polished with furniture wax.
If any details have diverged, the edges are smeared with PVA glue and pressed against each other with clamps.

It happens that the edge at the countertop of the headset is peeled off or kitchen table. It can be replaced with a new, matching color. This will require the edge itself, scissors, a construction knife, and an iron.

The edge is cut into pieces, according to the size of the countertop, with small allowances. First, blanks are made for the long sides, then for the short ones.
Then the iron is adjusted so that the edge does not overheat and swell.
The edge is evenly applied to the end. For convenience, you can put the countertop upside down.
With uniform, unhurried movements, they drive along the edge with an iron, as a result of which the glue is melted, and the edge is glued to the end.
While the glue has not cooled down, it is necessary to press the edge to the countertop, ironing with pressure along the edge with a piece of felt or a rag.
The excess edge at the corners is cut with scissors, trimmed with a knife.
The excess edge from above and below, if it does not fit in width, is cut off with a knife, gradually, towards the countertop. And then they pass again in one motion, applying the blade at an angle of about 45 degrees to the countertop.
Corner joints are lightly sanded with fine sandpaper.

Video: restoration of a burnt countertop

Swollen, the film peels off

The peel-off film can be glued back if this disadvantage is insignificant. For these purposes, ordinary PVA glue is suitable. The main thing is to get to all hard-to-reach places.

Video: gluing shrink film with PVA glue

When the problem becomes global, the film will have to be removed. This is done in the following way.

And after that, two options are possible: either paint the facades, or stick a new film.

Facade painting

If it is decided to paint, then the facades will need to be sanded to clean off the adhesive residue and level the surface. This applies to both MDF, chipboard, and solid wood. In places where the cutter has passed, the material may be rough. To prepare for painting, professionals recommend taking:

sandpaper P220-280 on foam rubber. It takes shape better and can be sanded into complex curves;
scotch brite P220-280 is a non-woven abrasive material, somewhat reminiscent of felt. They go through hard-to-reach places;
antisilicone - acts as a degreaser;
primer for plastic (also suitable for wood);
epoxy primer - needed for good adhesion;
acrylic primer - filling, for leveling the plane;
solvents.

If there is gloss on the facade, it is necessary to bring it down over the entire plane, to achieve a dull finish. Then carefully remove dust from the surface, degrease it and apply a primer for plastic. Then primed with epoxy primer, let it dry for 3-4 hours (if there is no paintwork, this step can be skipped) and primed with a pore-filling primer, sanded, preparing the facades for painting.

Spray paint is often used as a dye. When painting facades, the ends are first passed, then the paint is applied in a smooth movement from side to side, moving from bottom to top or top to bottom, with overlapping layers.

Decoupage

A popular way to update furniture is decoupage. It is typical for rustic interior styles, especially Provence.

	First of all, the handles are unscrewed from the facades.
	If there are any defects, they are eliminated.
	To remove the paintwork, you can use a remover. After applying the product with a brush, cover the facade with a film.
	Then, after holding the time, according to the instructions, the varnish is cleaned with a spatula, removing the film as it is cleaned. Washing is allowed to be reused.
	The surface is well sanded, dust is removed with a damp cloth.
	To achieve transparency of the paint, mix white acrylic varnish and white acrylic paint. Paint in the direction of the wood fibers.
	The drawing must be carefully cut with a clerical knife along the contour, fitting it to the size of the plane. To arrange the elements symmetrically, control the distances with a measuring tool.
	Apply a napkin and apply PVA glue on top of it.
	Then, after the glue dries, the surface is covered with fine sandpaper.
	Apply a thin layer of acrylic varnish. Sanded and varnished again.
	Additionally, facades can be decorated with putty. The composition is prepared as follows: oil putty is mixed with PVA glue, achieving the consistency of sour cream. Attach the stencil in the right place and apply putty over the stencil with a spatula.
	The resulting ornament is polished with fine sandpaper. If desired, you can tint putty. Then this area is covered with acrylic white varnish.
	Then a matte yacht varnish is applied to the surface.

Bonding self-adhesive film

If you wish to give MDF facades a certain texture, use a self-adhesive film. Before gluing the film, the facade is prepared as before painting. It is important to stick the film carefully, avoiding the appearance of bubbles.

First, a piece of film of suitable size is cut out with allowances of 2 cm on each side. Then the film is evenly applied to the edge of the facade, having previously removed 5-10 cm of the protective strip.
Glue the material in small areas, smoothing and gradually removing the protective film.
If bubbles nevertheless form and cannot be expelled, it is necessary to pierce them and release the air.

Countertop replacement

The chipboard tabletop sometimes becomes completely unusable if, for example, it is swollen from water. In this case, it is not necessary to order a new one. You can make your own tile countertop. Such countertops, firstly, are durable, and secondly, you can choose almost any design. It is fashionable to lay out a mosaic table top.

	The basis of the countertop is extruded polystyrene foam. It is installed on liquid nails.
	First, liquid nails are applied to the base, then sheets of expanded polystyrene are laid.
	A metal plinth is installed on liquid nails, protecting the ends of the countertop.
	Then corner plinth
	and a thin plinth for tiles.
	Then apply tile adhesive to the countertop.
	The same is done with tiles. And glue it to the tabletop.

Broken mounting holes

Chipboard tends not only to swell from water, but also to crumble under load. From frequent inaccurate opening of cabinet doors, self-tapping screws break holes and break out what is called "with the root". It is impossible to simply screw the self-tapping screw into the same place again. But there is one long-known way to repair broken holes, which is still successfully used.

If more serious damage occurs, when the laminate around the attachment point peels off, another method is used. Mix PVA glue and wood shavings. This composition fills the damage. Let it dry, and then screw in the self-tapping screw, as if it were a new surface.

Second life for chairs

Analyzing the methods of repairing kitchen furniture, it is necessary to say about the repair of chairs. The easiest way to upgrade is with a seat cover that will hide any scuffs, scratches or patches on the seat. If the chair has a hard seat, then it is enough to paint it, you can decorate it with decoupage. The work is carried out according to the same scheme as in the case of the restoration of facades. old chair with a soft seat must be tightened. Let's take a closer look at how to do this. Of the materials and tools you will need: medium grit sandpaper, primer, brushes different sizes, gloves, paint, batting, upholstery fabric, furniture stapler.

	First, remove the seat and remove the upholstery and filler.
	Then the wooden seat is covered with a primer, it has antiseptic properties. After primer, leave to dry completely.
	The chair itself must be sanded, then primed and repeat these two steps again. If you want to achieve the effect of a perfectly smooth surface, then you need to do additional sanding and priming, moreover, with a leveling primer.
	Then you can start coloring. It is recommended to start staining from the inside, bottom.
	Then the chair is turned over and paint is applied to its upper part. After drying for a day, the chair is painted with a second coat of paint.
	Leaving allowances of 4-5 cm, cut out a piece of fabric according to the size of the seat, two sides at once. Moreover, the fold of the fabric should coincide with the outer edge of the seat, i.e. parts will be connected together.
	Then the batting is cut out. It is enough to lay the fabric in 4 layers.
	All batting is fixed around the perimeter with a furniture stapler.
	Then lay out the upholstery with the wrong side up, put the seat down with batting.
	They pass with a stapler on the sides, then separately bend the upholstery at the corners, fix it with staples. Put the remaining piece of upholstery on top, fold the excess inside. And go through with a stapler or hot glue.
	Install the seat.

And it also happens that the tree cracks, and the chair begins to stagger. This problem is also self-correcting.

Video: how to fix a wobbly chair

This is how you can repair kitchen furniture. These are not all options. You can find many more ways to repair, original options for restoration and renovation. kitchen set, tables, chairs. But even using only these recommendations, it is possible to completely restore kitchen furniture, while spending only on consumables.

Kitchen renovation in Moscow

Kitchen deservedly is a favorite place in the living quarters of any person, whether a woman or a man. Repair is always a very time-consuming and expensive process that takes a lot of time and resources. In order to avoid finishing work and at the same time transform your kitchen, perfect fit replacement facades on the kitchen set in Moscow. Over time it takes replacement facades cuisine, because under the influence external factors(water, fat, steam) appearance loses its former sophistication and novelty. In order to troubleshoot problems, you should use a service such as repairkitchen furniture at home.

What's Included a set of works on the repair of a kitchen set in Moscow?

- Replacement kitchen linens

- Replacement facades

- Replacement countertops

Works on repair cuisine

- Replacement fittings and mechanisms in your kitchen furniture in Moscow and areas. Loose or fallen off doors can be fixed on new hinges by re-drilling their attachment points.

- Bar counter repair and islands

- Urgent repair kitchen furniture

Repair and/or installation of additional shelves

- Repair built-in furniture kitchen

Installation of closers and lifts.

The most common kitchen repair service in Moscow is replacement facades cuisine. Are you tired of the old set or do you want new changes in the kitchen? Tired of the same drawing on the facades or tired of milling, which has become obsolete? Repair facades cuisine allows you to quickly and inexpensively update the interior, return the furniture to its former functionality and beauty. Replacement facades- profitable and rational way to upgrade kitchens. If all the cases of your furniture are not damaged and can serve you for a long time, then you can only change facade part. New quality facades and countertops will also last for years. You don't have to do long-term repair and permanently free kitchen. Replacement kitchen facades in the upper or lower modules - this is a reason to change the design cuisine, at minimal cost.

Repair and replacement elements of kitchen furniture from any manufacturers in Russia, Italy, Finland, etc., including replacement countertops- these are the main works that our masters have to deal with at home in Moscow.

If you need to do any small repair, then all operations are carried out directly at the customer's home. We also carry out complex turnkey works, for the manufacture kitchens, replacement countertops, replacement facades, and we also manufacture custom-made furniture, if you need not only to repair old kitchen, a make new kitchen to order in Moscow.

‹ Collapse Description

Planning to update your kitchen? Tired of using old kitchen furniture? Annoyed by skewed doors, creaking drawers? Tired of falling handles, worn countertops or flaking furniture walls that ruin the whole look? We know how to fix your problem and drastically change the look of your kitchen at minimal cost.

Buying new furniture we want it to serve us for a long time. But, unfortunately, there is no such confidence in relation to kitchen furniture. The kitchen is the place where the whole family gathers every day. Here the hearth burns, the atmosphere of warmth and comfort reigns, here we receive guests. Kitchen furniture is used most actively. Moreover, it is daily exposed to high temperatures and moisture, so it quickly becomes unusable.

What to do, buy new kitchen furniture every year? But it's too burdensome. Reconcile and endure? Not necessary. Repair of kitchen furniture at home by our craftsmen is not only an affordable way to update your kitchen, but also an opportunity to make it even more functional and attractive. Remember, any damage is repairable. Thanks to our masters, there will be no trace of a malfunction. We will breathe new life into your kitchen.

Types of kitchen furniture repair

Every day, kitchen furniture is actively used, drops of fat, water, hot steam complete the picture. As a result, the following problems appear:

- cracks, chips;

- mechanical and rubbing parts wear out quickly;

- furniture cases begin to warp;

- accessories are damaged;

– coatings are damaged, paint peels off;

- the walls are stratified, chipboard and MDF swell;

- a fungus is formed.

If measures are not taken in a timely manner, kitchen furniture may simply fall apart and then the consequences will be much more deplorable: broken dishes, damaged facade, laminate, damaged kitchen appliances. Our masters eliminate malfunctions of any complexity and perform the following work:

countertop replacement;
replacement of kitchen facades from 2000 rubles m / sq.;
replacement of fittings, hinges, locks;
coating restoration;
repair of furniture cases, restoration of the geometry of lockers;
drawer repair;
banner of chairs, soft corners;
strengthening of buildings, etc..

Fortunately, our masters will fix most problems directly at your home. All work is carried out as quickly as possible and quality. At your request, we will restore the original look of the headset or radically change its design. Our company employs experienced furniture restorers who know how to transform your kitchen.

Also, our specialists have extensive experience in upholstery and upholstery of stools, kitchenettes. We use only modern durable fabrics that resist grease and moisture well. You choose the color yourself.

How long does a kitchen renovation take?

Maintenance and restoration of furniture can last from several hours to one or two days. Repair time depends on:

- on the complexity of the faults;

- quantity and size of restored furniture;

- additional requests.

Why should you contact us for help?

After the repair, the kitchen set will take on a new look;

When repairing kitchen furniture, our masters completely restore its functionality;

Our masters perform all work as quickly as possible.

Call the master by phone: 8 926 272 89 02

Furniture repair in Moscow is possible at home or in our workshops. We will do our best to cause you as little inconvenience as possible.

Remember, to transform your kitchen, it is not necessary to spend heavily on buying new furniture. We will do everything so that when you enter the kitchen, you can enjoy its beautiful view and gladly receive dear guests here..

A procedure familiar to many owners. When doors fail kitchen cabinet, drawers stop moving, stool legs loosen or other breakdowns occur, the owners call the “5 Masters” specialists. Employees with the necessary set of tools come to the address in any district of Moscow, as well as the nearest suburbs, in order to quickly eliminate the malfunctions that have arisen. We offer you to evaluate the convenience of inviting specialists to your home. We accept requests to call masters by phone or online.

Benefits of Calling a Kitchen Repair Specialist
on house:

If you do not have the skills to repair furnishings, you will be helped
professionals
You save time and money on transporting bulky furniture to
repair shop
You choose the time for the arrival of repairmen
interior items
Our employees will come on call to any district of Moscow, as well as the nearest
Moscow region
Calling employees of "5 Masters" to the house is free

When do you need to repair kitchen furniture in your home?

Items kitchen interior require repair almost more often than other pieces of furniture. This is explained simply: the owners regularly use the set for cooking and several times a day sit down at the set table. Due to daily use, lockers, shelves, chairs and tables quickly fail. Loose stools, a countertop cut with a knife, corners of the headset that have delaminated due to high humidity, sticking drawers - this can happen to every kitchen. Do not ignore the minor problems that arise with kitchen furniture in your home, because small troubles can turn into serious breakdowns. It is better to make repairs as soon as problems appear.

Kitchen furniture repair specialists at home perform any work, from simple to the most complex. Their responsibilities include reinforcing furniture cases, replacing door hinges, locks, fittings and roller mechanisms, elimination of squeaks, upholstery of sofas and chairs, as well as cosmetic repairs of kitchen units. The latter implies the elimination of fatty deposits, as well as scratches, chips and cracks that have arisen on the surface of a piece of furniture during operation. At the request of the owners, the craftsmen restore the original appearance of the headset or completely change its exterior, covering the surface furniture boards.

Repair of kitchen furniture at home can be quick or long, depending on the extent of the repair work. Minor flaws in interior items we eliminate on the same day. If we are talking about serious breakdowns, then the owners may have to wait a few days until the specialists make new ones. furniture details in the workshop. If necessary, we will involve restorers, as well as furniture reenactors, in the repair of the kitchen. They will help restore or completely transform the appearance of the kitchen set in your home. Contact us if you have any furniture breakdowns - from simple to the most serious. Our experts will quickly and accurately restore the elements of the situation of any year of manufacture and country of origin.

from 1600 rubles!

Master will arrive within
1 o'clock or convenient time!

and get 10% discount
for future work!

Kitchen furniture is interior items for a room intended for cooking and eating. The kitchen is equipped with both cabinet and upholstered furniture, therefore, for its repair, masters of a wide profile are required. The frequency of repairs is determined by the intensity of operation of the furniture.

The Domashnie Masters company offers customers from Moscow a kitchen furniture repair service. The company's specialists will repair upholstered and cabinet furniture from any materials with the use of professional tools in a qualitative and timely manner.

Repair of facades of kitchen furniture

We repair facades of kitchen furniture made of chipboard, MDF (hardboard), wood, metal and other materials with inserts and coatings of:

plastic;
glass;
enamels;
artificial veneer;
natural veneer.

Self-repair of facades can lead to final damage to furniture, since working with them requires qualifications, knowledge of the characteristics of materials, and the availability of professional tools. The masters of the company, thanks to many years of practice, are familiar with the properties of these materials and are provided modern equipment and necessary consumables for restoration of facades of kitchen furniture. When repairing facades, the company's specialists perform the following work: