To avoid the appearance on the walls of the apartment of traces of door handles that open wide, a do-it-yourself door stopper will help. It may vary in appearance. The design, shape, material, color, price, and place of its attachment differ in the limiters. The main thing is that this item fulfills its purpose, stopping the door beating against the wall when opened.

The limiter is used to ensure that when the door is opened, the handle does not hit the wall, thereby not spoiling its coating.

Floor stop for door

Such irreplaceable accessories can be purchased at the store. But it is possible to make them yourself. The simplest limiter is made of sheet steel. For manufacturing you need to purchase:

• steel;
• metal scissors;
• drill for metal;
• hammer;
• square;
• pencil;
• perforator;
• screwdriver;
• screws.

The floor limiter can be made from a self-tapping screw by screwing a wooden or metal knob onto it.

You can simply cut a strip of steel and bend it at a 90º angle, or even take and screw a ready-made furniture corner used in furniture installation to the floor. But it will not take much time to give the sheet an intricate shape with scissors. With a wider range of tools at hand, the steel stopper can be slitted or engraved. But, if there are no such tools, you can get by with painting or a layer of varnish.

Do not make parts protruding towards the door on the stopper, as this will ruin its coating. On the bottom side, 2 or more holes are drilled, with which the limiter will be attached to the floor. When mounting on a carpet, you should be especially careful, since the pile, when fastened, can wrap around the screw and, as a result, a hole is formed. It is better to cut a hole to the size of the stopper immediately and only then fix it.

Related article: Garbage stove in the country

You can place the door stopper with your own hands in any convenient place, there are no clear rules about its location. They are usually located on a line from the middle of the door leaf to its outer edge. The closer the stop is to the door frame, the more load falls on the door hinges, which loosen faster than usual. Therefore, the stopper is located approximately in the middle, slightly moving towards the edge.

When the place for the location of the stopper is chosen, the door is opened so that the distance from the lock handle to the wall is at least 1 cm. At this place, the limiter is installed. 2 holes are marked and drilled in the floor, a fixing dowel is inserted into one of which, and a pin or guide pin is inserted into the other. The dowel is hammered into the required hole, the limiter is put in place, and you need to carefully monitor that the pin also takes its place. The structure is finally fixed.

It is possible to carve a stopper out of wood, but this material may not be able to handle the stresses of a constantly opening door. Such a figure must be covered with several layers of durable parquet varnish.

Soft stops for doors

The soft limiter can be sewn from any fabric and decorated with bows, beads and buttons.

The figure of such a limiter can be any animal or figure. They are sewn from any fabric. Installation does not require special tools, and for tailoring you will need an almost standard set.

Have you made an expensive repair and want it to stay in perfect condition for as long as possible? We advise you to purchase a door opening limiter. It will be able to protect your furniture and wall decoration from damage that can be caused by the handle of a rapidly opening design. Also, the latch is an actual purchase for apartments where small children live, it is they who most often suffer from blows from a suddenly opened door. Read on to learn how not to make a mistake in choosing such a stopper.

There are many cases in which a door holder is simply necessary. This accessory is especially relevant if there are small children in the house, to whom a suddenly opened door can cause considerable harm. Also, a stopper is necessary if you want to keep the expensive wall decoration in its original form, because the door that opens due to a draft often hits the surface behind it.

When a door stop is needed:

• If you are afraid of scratching the walls or the doorknob, the stopper will be a real salvation for you;
• If you plan to bring heavy furniture into the room, such a holder will help you fix the door in the open position;
• When a baby appears in the house who crawls or begins to walk, the door holder comes in handy, it does not allow the little prankster to pinch his fingers and holds back the door during drafts.

At the moment, there is a huge variety of door stops suitable for a variety of interiors. These can be modern stainless steel holders, and wooden stoppers in the form of animal figures, and even devices sewn from fabric to hold doors open.

There are also stoppers with various mechanisms that make such accessories modern and very useful devices. Such devices, for example, include a latch with a built-in magnetic sensor.

Types of door stoppers

Door stoppers have their own classification. Due to the fact that such devices come in a variety of types, you can install them in a place convenient for yourself, make them part of the interior or hide them from prying eyes.

There are three main types of door holders. There are also not very common, but useful stoppers that are used in special cases. Knowing on what principles such devices work, you can choose the most suitable option for yourself.

Types of clamps:

1. Wall holders can limit the opening of the door or prevent it from slamming. In the first case, a silicone or metal retainer is attached to a wall or furniture wall. Such a device will not allow the opening door to damage the finish. This accessory is especially relevant if you have a warm floor, on which it will not work to install a floor stopper. The holder, which prevents the door from slamming, has two positions: in the first, the canvas opens and closes absolutely freely, and if the stopper is lowered, it will not allow the door to slam shut.
2. The floor clamp is mounted on the floor. This is one of the most popular types of stoppers. The design of such an accessory can be very different, which is why it enjoys such a hype.
3. The door stopper is most convenient in apartments where small children live. This device limits the opening angle of the door, so that the canvas opened due to a draft will not harm your baby.
4. A furniture door opener is also a very necessary thing. It is simply necessary if you own headsets with springless hinges or piano hangers. Such a device will protect the decoration of walls and furniture doors from damage.
5. Stoppers for door handles allow you to fix the door in the closed position. They are magnetic and mechanical. Such accessories are very appropriate in bathrooms and parental bedrooms.

Also, door stoppers differ in the materials from which they are made. The choice of door holders must be made not only depending on the design of the room where they will be used, but also taking into account their technological features. So the holder for massive canvases must be made of metal, and the stopper, which will be installed on the wall, is best made of soft material.

Floor door holders: the principle of operation and incredible designs

Floor holders for doors are the most popular fixtures of this type. They differ in original design and simple construction. If you opted for a floor fixer, then you have yet to decide which of the existing types of such devices will suit you best.

Floor stoppers made in the form of animal figures look especially original. It can be a funny hedgehog, a cute kitten or a devoted dog.

Stationary door holders are a device of two elements. The first part is a thin metal plate, and the second is a magnet. A piece of metal is installed at the bottom of the door leaf, and a magnetic device is attached in the place where the door should stop. Thus, the magnet attracts the metal to itself, and fixes the canvas in the desired position.

The stationary door holder is screwed to the floor in the right place. Such a device does not allow the structure to open wider than necessary. Since such an accessory is attached to the floor with self-tapping screws, it cannot be installed in rooms where a floor heating system is equipped. Otherwise, you may damage the heating elements.

The portable stopper consists of a thin part that can be pushed through the bottom of the door and a wide side that will hold the canvas in position. To install these accessories, you do not need to damage the floor covering. You can also buy one such device for the whole house, and rearrange it in the right room if necessary.

The holder, which is fixed at the bottom of the door, has a non-slip surface. Thus, the canvas cannot be moved from its place without applying a certain effort.

How to make a door stopper with your own hands

The door opening limiter is not difficult to do with your own hands. Creating such a device will not take you much time. The advantage of making a stopper yourself is not only to save money, but also that you can create an accessory with absolutely any design.

With your own hands, you can make both a stationary and a portable stopper. However, the second option looks more original.

A soft stopper is the easiest to make. To do this, you will need: fabric, sewing supplies, sintepuh and sand.

Such a door opener is a soft toy with a twisted tail. It is the tail that is placed under the door, and the body does not allow it to open.

The body with the tail of the animal is stuffed with sand, this part is responsible for holding the door in the desired position. The remaining elements of the product can be filled with sintepuh. Such a stopper looks very cute, but at the same time it is a convenient and functional thing.

Door stop options (video)

Door stoppers at first glance may seem like completely useless knick-knacks, but in some cases such a device is indispensable. You can purchase a door stop at a hardware store or make your own. Whichever option you choose, remember that all the accessories in the house should be in harmony with each other and with the surrounding decoration.

You are tired of loudly slamming doors and impartial chips on the walls left by the door leaf, so it's time to purchase and install a door opening limiter. Next, we will analyze in detail the types of such devices, and finally we will show how to install a door stopper with your own hands.

Door opening limiters are quite diverse.

The stool pushed under the door and a homemade wooden wedge are slowly disappearing into history. Now the industry produces a wide variety of stops, which are sometimes difficult to understand.

Limiter classification

In fact, the door stop is one of the varieties of small fittings. Doors are divided into entrance and interior doors, the weight and dimensions of the canvases can vary greatly, respectively, and the stops on the door are different.

In addition, door stops can perform different, sometimes opposite, functions. It’s one thing when you need a stop so that the canvas doesn’t hit the wall, and it’s completely different when you need to protect children’s fingers from a door that doesn’t close at the right time.

But how to make the right choice, if often an ordinary person has a rather vague idea of ​​what kind of mechanism he needs. First, let's go over the basic terms.

Original door stop design.

• Stops - designed to limit the angle of the door turn, and sometimes fix the door leaf at the end point when in contact with the stop;
• Chips - are needed to soften or prevent the impact of the door leaf on the wall or any other object, for example, furniture;
• Stoppers - these structures must rigidly fix the canvas at a certain point. The most prominent representative of stoppers can be called a well-known chain;
• Overlays - prevent the door from completely slamming, leaving a small gap between the jamb and the door leaf;
• Latches are, in fact, a kind of lock, the latch fixes the door in the closed state. There is still no consensus among experts whether to refer latches to locks or still to stops;
• Closer - as a rule, this is a limiter for opening the front door. The direct purpose of the closer is to ensure smooth closing of the doors, but there are models that allow you to fix the canvas open at a certain point.

Many modern door closers can be adjusted locally.

Despite the variety of terms and countless models, all these designs are divided into 3 fundamental areas:

1. Limiters installed on the floor;
2. Limiters mounted on the wall;
3. Limiters installed on the door itself.

Floor models

A floor stopper for a door is perhaps the most reliable option, because the floor is static, it will not go anywhere, plus the price of most floor models, as a rule, does not “crawl out” beyond 200 rubles.

The color of the permanently fixed post-post should be in harmony with the overall design.

Metal stops-columns are stationary limiters that are rigidly attached to the floor. The height of such an emphasis ranges from 3 to 7 cm, the average cylinder diameter is 20 - 30 mm. In order not to "cripple" the door on the column there is a groove with a rubber or polyurethane seal.

With proper installation, the column itself does not threaten anything, but the seals will have to be changed periodically. In the residential area of ​​​​an apartment or a private house, it is better not to put columns, since it is easy to stumble on them, but as a limiter for opening the front door, the column fits perfectly.

When choosing such a column, it is better to give preference to shiny and contrasting models. They are at least visible from afar and less likely that a person will stumble.

Semicircular door stop.

The semicircular door opening limiter looks like a quarter of a dissected ball with a shock-absorbing gasket. There is no fundamental difference in the operation of posts and semicircular stops, but when installing the latter, the installation angle must be taken into account so that the door leaf comes into contact with the rubber gasket and does not hit the metal.

The magnetic door stop keeps the door open.

A door stop equipped with a magnet is already a more functional design. A small magnet is built into the head of the stationary stop, and a counter metal plate is attached to the door, as a result, the door leaf is fixed when it comes into contact with the stop.

Of course, magnetic structures are not suitable for entrance doors, because the strength of the magnet is not enough to hold the canvas in gusts of wind, but in the room such stops work flawlessly.

Cork stops are only suitable for the corresponding design.

Cork, rubber and polyurethane stops are a variation of the same posts, the difference is only in the material. But before you put such an original emphasis, you need to think carefully, because a soft limiter is not a guarantee that you will not “beat off” your fingers about it, plus the cork is practically invisible on the carpet.

The ability to close the head of the stop in a latch mounted on the door jamb is quite a useful feature. Especially well, such devices have proven themselves on the front doors of offices, administrative buildings and shops, in general, wherever a simple latch can pop out by negligence or from a gust of wind.

The spring stopper is a good solution for temporarily fixing the door leaf.

The design solution is ingeniously simple: synthetic anti-slip "hedgehogs" are fixed on both sides of the flexible steel plate, you only need to slightly bend the plate and slide it under the doors.

Such a device is well suited for temporarily fixing doors, for example, if you need to bring furniture. With this emphasis, even if the door moves from an accidental push, expensive laminate or parquet will remain intact.

The wedge retainer is the simplest solution to the problem.

Wedge-shaped or as they are also called, mobile clamps are now made from different synthetic materials, but in fact these are the same wooden wedges that our grandfathers inserted under the doors, only the external surroundings have changed. Although synthetics must be given credit, such a door stopper does not slip on the floor.

The signal limiter can become the last bastion on the way of robbers. Cheaper models simply make a loud sound when the door leaf comes into contact with them, and the "advanced" stops silently send a radio signal to some kind of receiving device, for example, to a mobile phone or a security console.

wall models

Installing a door stop on a wall is an excellent solution for rooms where, for one reason or another, it is not desirable to fix the device to the floor, for example, expensive floor coverings, such as marble or natural parquet.

Classic wall stop for a door.

The cost of wall fixtures starts from 150 rubles, although this is not a lot, but still more than floor limiters.

The market leader here is a standard stop with a platform and a rubber shock absorber mounted on top of a metal rod. It is distinguished from the floor version of cork by the presence of a wider support platform and a stem with a length of 5 to 15 cm.

When choosing, you need to consider what material your wall is made of. There is no difference for monolithic brick or concrete walls, but for drywall you need to buy a device with a wide mounting platform (at least 100x100 mm), otherwise the GKL will simply break through from a point impact.

The simplest wall limiter with fixation on self-tapping screws.

The wall-mounted version of the magnetic device may differ from its floor-mounted "brother" only in the length of the stem, otherwise they are identical.

Often there is no way to fix the limiter on the floor, and rubber shock absorbers with a rod leave hard-hitting marks on the door leaf. In this case, a soft pad on the wall under the handle will help you.

Soft synthetics will smoothly absorb the blow, you don’t need to drill a wall to mount the stop, just stick the fixture on double-sided tape, and most importantly there are a lot of design options and choosing a model for your interior is not difficult.

Soft model with support under the handle

There are in the line of wall fixtures and stops with a reliable lock. As shown in the photo below, the mechanism itself is attached to the wall with self-tapping screws, and the hook with the platform is screwed from the bottom end on the door leaf.

The principle of operation is simple: a rounded door hook, approaching the stopper, lifts the movable part and, thanks to the spring, the latch clings. The only inconvenience is that to release the doors, the latch will have to be pushed back manually.

Wall version of the stop with a latch.

Door fittings

The beauty is that if we are talking about wooden or plastic doors, then you only need a screwdriver to fix such a limiter, and in some cases you can get by with one glue. Plus the walls and floor will remain intact.

In folding metal stops, the base plate is screwed to the door leaf with self-tapping screws, but during installation, you need to carefully consider setting the angle of inclination of the limiter relative to the floor, an acute angle can cause the mechanism to break. The optimal slope is around 45º.

In addition, when choosing, it is better to give preference to mechanisms in which there is a folding spring, they are an order of magnitude more reliable.

Folding metal overdoor limiter.

The tape stop can be safely called a symbol of simplicity. Self-tapping pads are attached on both sides of the strong tape, you just need to screw these pads to the doors and the jamb.

True, the appearance of this limiter leaves much to be desired, plus such tapes fray or tear rather quickly.

If you still decide to buy a tape stop, then it is better to choose elastic stretchable models, their price is not much higher, but such stops are more convenient to use.

Tape stop is considered one of the simplest and most affordable options.

The retractable overdoor stop is a rod with a kind of brake shoe. It is installed in a vertical position and you yourself can decide where exactly to fix the structure.

The retractable overdoor stop is a fairly compact and convenient device.

The sliding model is designed to rigidly fix the door leaf at certain points, there may be several points, it all depends on the number of cutouts in the solid base groove.

This device cannot be called completely over the door, since the base part with a groove is attached to the door jamb, and only the movable stem is fixed on the canvas. Although this is not essential, on some models the fasteners can be interchanged.

The undoubted advantage of such an emphasis is the installation at the top of the doors, where it does not interfere with anyone. On the other hand, to release the stem from the locking groove, you will have to reach it, which is not always convenient.

One of the popular models of sliding stop.

Soft slips protect a door from slamming. These devices are especially convenient in children's rooms, with such pads your child's fingers are much less likely to be squeezed in the door. There is no need to talk about installation at all, the rubber band is simply put on the door.

The soft slip is designed to protect the doors from accidental slamming.

Installation technique

Installing a door stop is pretty easy. We will not talk about gluing options, you can handle this yourself, as for fixing on self-tapping screws, the instruction is something like this:

1. We install a door with a gap between the handle and the wall of about 20 mm and mark the position on the floor;
2. According to the mark on the floor, set the emphasis at the desired angle;
3. We drill a hole for the dowel for the self-tapping screw and insert the dowel itself;
4. We fasten the stop with a self-tapping screw to the floor.

Wall and door opening stops are mounted in approximately the same way, so there is no point in retelling this simple instruction.

Conclusion

We tried to most fully reflect all types of door stops. Watch the video in this article for more information on this topic.

There are quite a few options for making limiters for a door with your own hands. Each of them is worthy of attention, as it allows you to equip a stopper for the canvas with minimal cost and personal effort. Which method to choose depends on personal preference. It is worth considering the most popular options.

You can easily make a door stopper with your own hands

Functions and types of limiters

Installing a limiter is a necessary measure if the canvas can touch furniture when plowing. This is especially true if there is glass or mirrors near the passage. In this case, use floor, door stoppers or items that can replace them.

The stopper performs the following functions:

• limiting the course of the canvas when plowing;
• protection of the door and nearby objects from damage;
• decorative addition to the interior.

With the help of the limiter, you can protect the door and nearby objects

You can make such a device with your own hands, despite the fact that such products are sold in many furniture and hardware stores. There are many options for execution, but it is worth noting the most successful of them.

soft option

The most interesting in execution is the soft limiter. Making such a product for the door with your own hands is not difficult. The principle of its manufacture is based on the creation of a tilde with synthetic filling.

In order for such a stopper to have sufficient mass, prepare sand, small pebbles or some similar materials in advance.

A soft limiter is hung on the handle on the side of the door into which it swings open. To do this, you need to provide for the presence of a special loop.

The design and coloring of a kind of doll is a personal matter for everyone. You can find ready-made patterns of patterns or draw your own version yourself.

The soft limiter additionally serves as an interior decoration

To sew such a stopper, you will need fabric, threads, pins and a synthetic winterizer or holofiber for filling. The volume of the doll should be sufficient to soften the blow. All parts are cut in duplicate. They are folded face to face and stitched, leaving a small area unsewn for filling. Each element is turned inside out, stuffed with filler and sewn up with a blind seam. Then you need to sew all the fragments together.

furniture limiter

The easiest option is to take a ready-made stopper. Such products can be found among furniture fittings. You can even use a limiter from an old cabinet.

Do-it-yourself installation of a furniture door stop is done using a screwdriver and self-tapping screws. One part of the product is fixed on the box, and the second - on the canvas itself. In this case, the length of the rod can be adjusted, which allows you to choose the degree of restriction of movement of the door.

The easiest option is to use a ready-made furniture limiter

floor stopper

The best option for most rooms is a stationary floor stopper for the door. It can also be made by hand. At its core, this design is very simple, so you will need a minimal set of tools. Let's consider two options:

1. Wood. Take a small bar, preferably round in cross section. Measure the required distance. You can make a stopper 3-5 cm high, or you can increase it to 10 cm. If a fine tree is used, then you need to immediately treat it with a stain of the desired shade and open it with varnish. At the same time, please note that the entire surface of the part must be carefully sanded. Then take a double self-tapping screw or stud and screw it in from the back side from the end. For installation, you need to choose a place on the floor, drill a hole, insert the dowel and drive the stopper there, gradually twisting it to the very end.
2. Metal. The principle of creating such a limiter is the same as for a wooden model, but there are subtleties here. First you need to cut the tube of the desired size. A great option is stainless steel. For the top of the limiter, take a plastic plug. On the reverse side, fix the plate with screws. The installation principle is as follows: select a place on the floor, drill holes for the plate and fix it with screws.

Types of floor stopper for the door

In order for the edges of the door leaf not to beat off the limiter, additionally fasten rubber bands on it. For example, you can take plumbing volumetric gaskets.

A door stopper is a great option that allows you to protect the canvas itself and nearby objects from damage. In addition, it can become a stylish addition to the interior, especially if you do everything yourself, taking into account personal wishes.

Probably, every person has encountered a problem when the door leaf slams loudly. In addition, when opening the door from hitting the wall, chips remain on it, which also do not decorate the room. To get rid of such problems once and for all, it is enough to buy and install a door stop. First you need to deal with the existing proposal, choose the type of limiter that is best suited in a particular case, and any home master can install it with his own hands.

What are door stops and locks for?

If you often hear the sound of a door hitting when you open it in your house, a door stopper will help solve this problem once and for all. It is a device that provides protection for doors, walls and nearby objects from chips and damage. This is a small detail, but it helps to significantly increase the life of the door leaf, as well as protect the walls from damage when the door is carelessly opened. By installing such a device, you will be relieved of the need to frequently change the decoration of the wall next to the entrance.

Without installing a door stop, opening the door may damage the wall or nearby furniture.

The door stop allows you to set the maximum opening width of the door leaf or reduce the speed of its movement. Some models securely fix the door in a given position, depriving it of the ability to open or close on its own. There is a fairly wide selection of such devices, which differ from each other both in shape and design, and in appearance.

Types of door stops

Door stops vary:

• at the place of installation - they are floor, wall or door;
• according to the principle of operation - there are ordinary, magnetic, vacuum and mechanical stops.

Since interior and entrance doors have different sizes and weights, different limiters are used for them. An ordinary person, faced with the problem of choosing such a device, may be confused by the available choice. To prevent this from happening, you need to navigate in the terms used:

• stop - a device that limits the opening angle of the web, and sometimes fixes it when it reaches the end point;

  The stop allows you to fix the canvas in the desired position

• bump stop - prevents the canvas from hitting a wall, furniture or other object that is in the way of opening the door;

  The chipper prevents the door leaf from hitting the wall

• stopper - designed to fix the door in a certain position;

  The stopper allows you to fix the door in the desired position

• overlay - does not allow the door to slam arbitrarily;

  The overlay does not allow the door to close arbitrarily

• latch - fixes the canvas in the closed position. Some experts attribute such a device to locks, others to stops;

  The latch secures the door in the closed position

• closer - in addition to ensuring smooth closing of the door leaf, it also limits the angle of its opening.

  The closer limits the opening angle of the door leaf and ensures its smooth closing

Floor models

Floor door stoppers are installed directly on the floor covering and are divided into two types according to the type of their action:

• holding the door leaf in a predetermined position;
• controlling the degree of opening of the door.

According to the installation method, such limiters are divided into:

1. Mobile or mobile. In specialized stores, such stops are presented in a wide range and can have a wide variety of designs: in the form of letters, toys, wedges, etc. Models that are worn on the lower edge of the door leaf have become widespread. Such limiters have an anti-slip coating, abut on both sides of the door and do not allow it to move in either direction.

   Mobile floor limiter can have a wide variety of shapes

2. Stationary. Such models are mounted on the floor in a certain place and are intended for permanent use. They can be of several types:
   

When choosing a place for mounting a floor limiter, one must take into account the fact that it should not interfere with free movement, otherwise it is easy to injure the leg by hitting the latch rigidly screwed to the floor.

wall models

In those rooms where it is not possible or undesirable to fix the door stop on the floor (expensive parquet, natural marble floor or other unique coating), wall models are an excellent solution. Such devices are slightly more expensive than outdoor ones and there are several types:

• in the form of a rod - they are an emphasis with a platform for mounting and a rubber shock absorber mounted on a rod, the length of which can vary from 5 to 15 cm. Before buying a wall-mounted model, you need to decide which wall you will mount it on. There is no difference for a brick, and if it is made of drywall, then it is necessary that the size of the fastening part be at least 10x10 cm. This will ensure a reliable fastening of the stop, and the wall will not break through from the impact;

  A conventional wall stop is a stop with a mounting platform

• with a magnetic latch - they differ from the floor version only in the place of installation;
• overlays. If you think that a wall-mounted shock absorber with a stem does not look very beautiful, you can install a pad under the handle. It is located on the wall opposite the door handle and is usually attached to double-sided tape, so you don’t have to drill the wall;

  To limit the opening of the door on the wall, they often mount an overlay under the handle.

• with fixing the position of the door. In this case, the stopper is attached to the wall, and the hook is attached to the door. When the door is opened, the hook rises and the canvas is securely fixed in the open position. To close the door, such a latch must be unlocked manually.

  After opening the door, the hook securely fixes it in the open position.

Door fittings

Overdoor stops are installed directly on the door leaf, so the walls and floor are not damaged. Fastening is done with glue or self-tapping screws.

1. The simplest is the tape stop. It is a strong tape, at the ends of which there are places for fixing it to the jamb and the canvas. In order for the tape limiter to serve for a long time, it is necessary to purchase models that have high strength and elasticity.

   The tape limiter has special platforms for fastening to the canvas and the jamb

2. For an entrance door, a hinged stop would be an excellent option. During installation, the angle of stop relative to the floor must be observed. The best option is when it is 45 o, at a smaller angle, the mechanism may break.

   The folding stop is activated by pressing the foot, and in the retracted position it securely snaps onto the clip

The retractable stop is made with a rod and a brake shoe. Its installation is carried out in a vertical position. You can also operate such a device with your foot, and in order to raise it, you will need to manually bend the side plate.

Raise the retractable stop with your hands

The sliding door stop allows you to fix the canvas at different points, their number depends on the number of cutouts in the groove of the device. A rod is fixed on the canvas, and the device itself is installed on the door jamb. Since this limiter is installed in the upper part of the leaf, it does not interfere with the operation of the door.

The sliding limiter allows you to fix the canvas at several points

3. Soft overlays. Protect the door from accidental slamming. Their use allows you to protect children's hands from the possibility of being squeezed by doors. To install such devices, simply put them on the door leaf.

   Soft pads are installed on the door leaf and protect hands from accidentally getting into the space between the door and the jamb

Anti-vandal restraints

There are models of limiters that allow you to protect the house from illegal entry. The simplest options can simply make a loud sound when in contact with the door leaf. More expensive models send an alarm signal to the security console or mobile phone.

Anti-vandal limiter allows you to protect the house from thieves

This type of limiters can be both floor and over-door. Floor models are available in the form of polymer wedges or other suitable shape. Overdoor stops are put on the door leaf and are also made of soft materials. The free-standing stops do not need to be locked in place, so they can be used anywhere and anytime.

Freely positioned stops do not require fastening and can fix the door in any position

Magnetic or vacuum stops

A feature of the magnetic limiter is that it not only prevents the door from swinging open at an angle greater than the specified one, but also ensures its fixation in the open position. A metal plate is installed on the canvas, and a magnet is placed on the limiter itself. To fix doors of different weights, you need to choose a magnet of the appropriate power.

Instead of a magnet, a vacuum lock can be used on such limiters. In this case, a rubber suction cup is installed on the door, which repeats the shape of the limiter. When opening the door, the suction cup is securely connected to the limiter and ensures that the door leaf is held open.

Vacuum stop keeps door open with suction cup

ball detents

Ball devices are designed to fix the door in the closed position and do not allow it to open spontaneously. These are small devices, one part of which is mounted in the door leaf, and the second - on the door jamb. These models are usually used on interior doors that do not need long-term locking. Due to the presence of an internal spring, the ball securely fixes the door, and after pressing the canvas, even a child can open it.

The ball lock securely holds the door closed, and it will not be difficult to open it if necessary

Video: types of door stops

Installation of door opening limiters

Most often, floor or wall door stops are used, so we will consider the installation process using their example. To complete the work you will need:

Mounting the floor stop

Consider the installation of a conventional metal floor door stop. It can have a different shape, for example, in the form of a pin or a hemisphere, as well as different heights.

Work on the installation of the floor limiter is carried out in the following sequence:

1. Preparation of tools and inspection of the limiter assembly. Usually, the kit includes a screw and a dowel for fixing the stop, but if they are not there, you need to prepare the fasteners separately.

   Checking the complete set of the door stop

2. Site selection and marking. For the correct choice of the installation location, it is necessary to open the door leaf so that it does not reach the wall or furniture by 3–5 cm. Don't forget to consider the size of the door handle. The place for the stop is chosen approximately in the center of the door. Mark the installation site and check again if everything is done correctly.
3. Creating a hole. Using a drill, make a hole in the floor and insert a dowel into it. For concrete pavement, a hammer drill must be used.
   

   A hole is made in the floor into which a plastic dowel is inserted.

4. Limiter installation. Install the door stop and fix it with one or more self-tapping screws. If the limiter has the form of a hemisphere, it must be turned so that the canvas is in tight contact with the rubber pad.

   Using a self-tapping screw, fix the limiter

To keep the brass floor stopper shiny, it is recommended to periodically open it with varnish.

Video: installing a floor stop

Mounting the wall stop

If you want the limiter not to interfere with free movement around the room, you can install it on the wall. Installation of wall models is carried out in the same sequence as the floor options. The only difference will be that such a device is mounted on the wall, and not on the floor.

Repair of door opening limiters

A feature of door latches is that they have a simple design, so they have practically nothing to fail.

The main breakdowns of door stops will depend on the type of device:

• failure of the rubber lining. If the rubber lining is damaged on the floor or wall model of the limiter, then it must be replaced;
• weakening of the suction cup. If the suction cup is damaged in the vacuum limiter, then it will not provide reliable fixation of the web and it must be replaced;
• damage to the stop for over-door models is eliminated by replacing such a device;
• the weakening of the spring in the ball stopper leads to the fact that it cannot perform its functions. This device must be replaced.